Determine the current as a function of time

Assignment Help Electrical Engineering
Reference no: EM13288796

An unusual capacitor has a capacitance that is a function of timegiven by
C = 2 + cos(2000t) μF
in which the arugument of the cosine functionis in radians. A constant voltage of 50V is applied to this capacitor. Determine the current as a function of time.

Reference no: EM13288796

Questions Cloud

Explain what is the molarity of h2c4h4o6 : What is the molarity of H2C4H4O6 if 31.75 mL of 0.1749 M KOH are required to react with 10.04 mL of H2C4H4O6 solution according to the reaction below
How much work does the intern do by pushing the patient : An intern pushes a 72 kg patient on a 15 kg gurney, producing an acceleration of 0.60 m/s2. How much work does the intern do by pushing the patient and gurney through a distance of 2.5 m
Find the peak power delivered to the machine : The rms current in a copy machine is 5.26 A, and the resistance of the machine is 19.7?. find the peak power delivered to the machine
Explain assuming that seawater has a total ion concentration : Assuming that seawater has a total ion concentration (a.k.a colligative molarity) of 1.10 Mc, calculate how many liters of seawater are needed to produce 15.4 L of fresh water at 20 °C with an applied pressure of 75.0 bar.
Determine the current as a function of time : An unusual capacitor has a capacitance that is a function of time given by C = 2 + cos(2000t) μF in which the arugument of the cosine functionis in radians. A constant voltage of 50V is applied to this capacitor.
Determine the maximum thickness of ice : The rear window of a van is coated with a layer of ice at 0°C. The density of ice is 917 kg/m3, What is the maximum thickness of ice above this area that the defroster can melt in 3.9 minutes
Explain the ph after the addition of each acid : A 119.6ml sample of 0.110M methylamine (CH3NH2) is titrated with 0.255 M HNO3 . Calculate the pH after the addition of each of the following volumes of acid.
Derive a circuit using d flip-flops to generate clock signal : Given a 100MHz clock signal, derive a circuit using D flip-flops to generate 50HHz and 25MHz clock signals. Draw a timing diagram for all three clock signals, assuming reasonable delays.
What is the resistance of the heater wire in the blanket : An electric blanket is connected to a 120-V outlet, What is the resistance of the heater wire in the blanket

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the joint probability distribution function

Two random variables X and Y have a joint probability density function given by f(x,y) =kxy 0

  Find electric potential of point a with respect to point b

Given the electric field E= ar (18/r2)(V/m), find the electric potential of point A with respect topoint B where A is at +2m and B is at -4m on the z-axis.

  How much current can flow through the human conducting path

If the resistance of dry skin is 5 k? and accidental contact is made with a conductor that is at a voltage of 120 V, how much current can flow through the human conducting path. If contact with this same conductor is maintained for 10 s

  What is the percentage of distortion level at the frequency

The sampling frequency in a DSP system is fs = 8khz kHz. A hold circuit is used after the DAC device. What is the percentage of distortion level at the frequency f= 3.4 kHz

  Design a wafer structure for the laser

Graded-index separate confinement double heterostructure (GRIN-SCH) InGaAs/GaAs lasers with various cavity lengths were tested in the lab. The 100m wide oxide strip lasers consists of two pairs of 10nm In0.2Ga0.8As quantum-well (QW).

  Write an expression for the h field of the wave in medium 2

Using the solution for , write an expression for the H field of the wave in medium 2, which is due to the surface-current source. Hint: Since the current-sheet source is independent of x and y, so will be the wave it generates - this is a plane wa..

  Design a low-pass filter with a cutoff frequency

A) Design a low-pass filter with a cutoff frequency of 12 kHz. Use 0.15 uF capacitor and an appropriate resistor. B) Sketch and label the circuit. C) What is the gain of the filter at a frequency of 20 kHz Give your answer both as ratio (Vout/Vin) an..

  How many signal levels are needed to achieve the datarate

The result of part a) is the upperlimit. However, as a practical matter, better error performancewill be achieved at a lower data rate. Assume wechoose a data rate of 2/3 teh maximum theoretical limit. How many signal levels are needed to achieve ..

  Obtain the phasor expression for the wave magnetic field

frequency 6GHz propagating in vacuum is comprised of two components which are in spatial and temporal quadrature. The phasor expression of the wave electric field is given to be. obtain the phasor expression for the wave magnetic field.

  Discuss the purpose of the two timers in the ladder logic

he operation of the system requires that, before any change of motion direction, the motor must be in a full stop by push the "STOP" button Assuming bother timer TD1 and TD2 have the same preset time of 1 minute

  Estimate how long bus signal remains at a valid logic level

ON a three-state bus, ten FCT three-state buffers are driving ten FCT inputs and a 4.7kΩ pull-up resistor to 5V. Assuming that no other devices are driving the bus, estimate how long the bus signal remains at a valid logic level

  Determine limits if the amplifier is replaced by opa300 unit

a 60-kHz sinusoidal signal is applied to an amplifier with a gain of k=2. the circuit is built with an lm741 opamp with power supplies +-13V. find the largest amplitude the signal may have before it is limited by slew rate constraints.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd