Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Given a 1-phase 50 kVA 12.47 kV pf = 0.8 lagging static loada. Modeling the load as constant complex power, determine the correct value for S and I.b. Modeling the load as constant complex impedance, determine the correct value for Z and I.c. Suppose the load model of (a) is used in a 12.47 kV circuit. What is the value of S and I if the system voltage rises 5% (to 13.09 kV)?d. Suppose the load model of (b) is used in a 12.47 kV circuit. What is the value of S and I if the system voltage rises 5% (to 13.09 kV)?
An OpAMP has a GBWP of 100MHz and a slew rate of 10V/us and AVoc = 160dB at DC. Assume VCC = +/- 15 Volts. a. If the opamp is configured as a non inverting amplifier with voltage gain of 50.
A Vs equals 1V source impedance 25ohms is connected by a switch to a 50-ohms lossless air transmission line 1 m long, terminated in a load of 30-ohms. At time t=0s, the switch is closed instantaneously to launch a step voltage down the line.
A glass tube with a cross-sectional area of 9^-2 m^2 contains an ionizd gas. The densities are 10^15 positive ions/m^ and 10^11 free electrons/m^3. Under the influence of an applied voltage, the postive ions are moving.
When the two windings are connected to a a.c supply of 50hz, the field current is 0.1A, the armature current is 100A and the phase difference between them is 60 degree. calculate the average torque and maximum torque.
Determine the ROM size and contents to implement a function which converts a sign and magnitude number from -5 to +6 to two's complement format.
transfer function: T(s)=1/(0.1s+1) with all initail conditions at 0 a) if the input is 1.5sin(2t)*u(t) find the steady state value of the output b) after the input is applied, approximately how long will it take for the steady state value you found i..
Vo(t) = RC (dVi(t)/dt). Suppose you have a triangle waveform as input to the differentiator with 100pF capacitance and 100 Ohms. The peak to peak voltage of the triangle waveform is 10Vpp and its frequency is 100k Hz.
Find the Laplace transform of a rectangular voltage pulse that is 0 V until time 0 s, then jumps to 5 V and stays there until time 2 ms, then returns to 0 V and stays there after time 2 ms. Hint: express the pulse in terms of unit step functions.
Find the inverse z-transform, x(n), of the following functions by bringing them into a form such that you can look up the inverse z-transform from the tables. This will require some algebraic and /or trigonometric manipulation/calculation.
a) Find the code word transmitted when the data word is 101100011011. b) Draw the LFSR circuit to generate the CRC. Generate the CRC by applying the data pattern to the LFSR and verify the answer in part a.
The voltage drops across three resistors in series are measured 10V, 15V, and 25V. If the largest resistor is 47 ohms, what is the value of the smallest resistor?
Design a low pass FIR filter for 10 kHz sampling, with a pass band edge at 2 kHz, a stop band edge at 3 kHz, and 20 dB stop band attenuation. Find the impulse response and the difference equation for the filter.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd