Determine the convection heat loss

Assignment Help Mechanical Engineering
Reference no: EM13946739

Determine the convection heat loss from both the top and the bottom of a flat plate at T= 80°C with air in parallel flow at Too = 25°C, uoo = 3 m/s. The plate   is = 1 mm thick, = 25 mm   long,   and   of depth= 50 mm. Neglect the heat loss from the edges of the plate. Compare the convection heat loss from the plate to the convection heat loss from an L= 50-mm-long cylinder of the same volume as that of the plate. The convective conditions associated with the cylinder are the same as those associated with the plate.

Reference no: EM13946739

Questions Cloud

Calculate voltage v : Calculate voltage V0 (by hand). Show the work below.
High-tension line has an electrical resistance : A 25-mm-diameter, high-tension line has an electrical resistance of 10-4  !1/m and is transmitting a current of 1000 A. If ambient air at 10°C and 5 m/s is in cross flow over the line, what is its surface temperature?
Diameter experiencing cross flow of water : A computer code is being developed to analyze a tem- perature sensor of 12.5-mm diameter experiencing cross flow of water with a free stream temperature of 80°C and variable velocity.
Estimate the equilibrium temperature rise : Estimate the equilibrium temperature rise and estimate the time constant - write an expression for the estimated curve (theta as a function of time) using the numerical results obtained in parts a and b.
Determine the convection heat loss : Determine the convection heat loss from both the top and the bottom of a flat plate at Ts = 80°C with air in parallel flow at Too = 25°C, uoo = 3 m/s.
Temperature of wire and free stream temperature : For a fluid of arbitrary Prandtl number, develop an expression for its velocity in terms of the difference between the temperature of the wire and the free stream temperature of the fluid.
Company do to get back to full capacity : Many major corporations have been greatly affected by the recent horrific tragedies in the Northeast with Hurricane Sandy and in Japan a few years ago with the large earthquake. How has this affected the global economy? In a one to two page paper, di..
Self-reflection rubric to evaluate the effectiveness : For this week's journal, use this self-reflection rubric to evaluate the effectiveness of your lesson plan from Week Four. Elaborate on the areas of strength in your lesson plan, as well as those areas in need of improvement.
Identify specific state tribal and federal organizations : Identify specific local, state, tribal, and federal organizations that have equities in the SWB region. Identify existing organizational structures that are either complimentary and supportive, or redundant and inefficient.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd