Determine the contact ratio and the diametral pitch

Assignment Help Mechanical Engineering
Reference no: EM131377655

An 18-tooth pinion having a 20° pressure angle meshes with a 36-tooth gear. The center distance is 10 in. The pinion has stub teeth. The gear has full-depth involute teeth. Determine the contact ratio (tooth intervals in contact) and the diametral pitch.

Reference no: EM131377655

Questions Cloud

Find the pitch diameter of the gear : For a gear having an outside diameter of 3.000 in., full-depth involute gear teeth with a diametral pitch of 20, and a 20° pressure angle, find the pitch diameter of the gear, the circular pitch, the addendum, the dedendum, and the number of gear ..
Do given facts sustain an action for fraud in the inducement : After three years without earning a profit, the plaintiffs sued Division West for fraud. Do these facts sustain an action for fraud in the inducement?
Changing american family : Define societal problems and analyze potential political and economic solutions to judge those that provide the greatest good for the greatest number.
Analyze the prioritizing process at dd williamson : Write a four to six (4-6) page paper in which you: 1.Analyze the prioritizing process at D. D. Williamson. 2.Suggest two (2) recommendations to improve the prioritizing process. 3.Create a scenario where the implemented process at D. D. Williamson..
Determine the contact ratio and the diametral pitch : An 18-tooth pinion having a 20° pressure angle meshes with a 36-tooth gear. The center distance is 10 in. The pinion has stub teeth. The gear has full-depth involute teeth.
Is schmalz correct in his assertion : Schmalz now sues his former employer for the severance pay, claiming that he signed the release under duress. Is Schmalz correct in his assertion?
What are the new values for contact ratio and pressure angle : If the center distance is increased by 0.125 in., what are the new values for the contact ratio and the pressure angle?
Should the guarantee agreement be set aside due to duress : As a result, the Haumonts signed the agreement, encumbering their previously debtfree family farm for more than $628,000. Should the guarantee agreement be set aside due to duress?
Whether the deed was executed as a result of undue influence : Conrad brought this suit to cancel the deed, claiming it was the result of Laurence's undue influence. Explain whether the deed was executed as a result of undue influence.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Formula for total output possibility set for goods

Compute a formula for the total output possibility set for goods 1 and 2 and draw it when

  What is plc

What is PLC (Programmable Logic Controller)?

  Development of software for the offshore oil industry

As a software project manager in a company that specializes in the development of software for the offshore oil industry, you have been given the task of discovering the factors that affect the maintainability of the systems developed by your comp..

  Design a pair of nakamura balance shafts

Design a pair of Nakamura balance shafts to cancel the shaking force and reduce torque oscillations in the engine shown in Figure 14-18 (p. 662).

  Dtermine a the compressor power in kw b the refrigerating

a vapor compression refrigeration cycle operates at a steady state with refrigerant 134a as the working fluid.

  What is the density of electrons in the conduction band

If we add an impurity that increases the density of electrons (the number per cubic meter) in the conduction band tenfold, what will be the density of holes in the valence band?

  Assume that the internal energy and specific volume of

the pressure of 200 kgs of water is to be increased from 1 atm to 4 mpa. the water enters through a 20-cm-diameter pipe

  Determine a the rate of heat transfer to water and b the

saturated steam at 110 c condenses on the outside of a 3-m long 7-cm-diameter thin horizontal copper tube by cooling

  Assuming a transition reynolds number of 5 x 105 determine

assuming a transition reynolds number of 5 x 105 determine the distance from the leading edge of a flat plate at which

  Determine the efficiency of the screw

In testing the design of the screw-lift jack shown, 12 turns of the handle are required to elevate the lifting pad 1 in. If a force F = 10 lb applied normal to the crank is required to elevate a load L = 2700 lb, determine the efficiency e of the ..

  Calculate the height in meters of a column of water

If we had only a ruler and a clock as measuring devices, how could we measure the density of water?

  Determine the vertical force

The 4 lb pulley has a diameter of 1 ft and the axle has a diameter of 1 in. if the coefficient of kinetic friction between the axle and the pulley is 0.20, determine the vertical force P on the rope required to lift the 20 lb block at constant vel..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd