Determine the concentration of the pit''s overflow stream

Assignment Help Civil Engineering
Reference no: EM13563627

A company has been discharging its waste into a holding pit for a long time. For the last several years, the pit has been full and overflowing into a local river. The waste concentration has been nearly constant at 10 mg/L of the pollutant of interest. At this concentration, there have been no adverse effects on the stream. Suddenly, there is a process change and the contaminant in the waste stream goes up to 100 mg/L. Given that the waste stream flow rate is 100,000 L/day and the holding pit volume is 1.0 million liters, determine the concentration of the pit's overflow stream after 10 days.

Reference no: EM13563627

Questions Cloud

What is the retention time for this lake : A small lake with volume of 20,000 m^3 has no natural pollutant sources. However, a sewage pipe discharges sewage containing an organic polluntant into the lake. Conditions in the sewage pipe are Qs= 0.5 m^3/s, and Cs= 100mg/L.
Compute the accuracy and compute the final coordinates : The Field data and the fixed data follow for each of six traverses. The forward direction is given by the alphabeteical order of the station names. Each angle is measured clockwise from the back direction to the forward direction so that  they are on..
What is the approximate diameter of an oil molecule : Given an oildroplet with a mass of 7.59e-7 kg and a density of 952 kg/m^3 that spreads out to form a circle with a radius of 42.2 cm on the water surface, what is the approximate diameter of an oil molecule
Calculate the work done by an external agent : Calculate the work done by an external agent during anisothermal compression of 1.00 mol of oxygen from a volume of24.0 L at 0°C and 1.00 atmpressure to 17.5 L
Determine the concentration of the pit''s overflow stream : A company has been discharging its waste into a holding pit for a long time. For the last several years, the pit has been full and overflowing into a local river. The waste concentration has been nearly constant at 10 mg/L of the pollutant of interes..
What would be the resistance on a level road : An automobile has been designed to maintain a constant speed of 55 mph on a +5% grade. The weight of the vehicle when fully loaded is 6000 lbs. What is the total resistance in still air of this vehicle? What would be the resistance on a level road?
What is the partial pressure of each gass componet at : A 1-m^3 volume tank contains a mixture of 18.32 moles of oxygen, 16.40 moles of Nitrogen, and 6.15 moles of carbondioxide. What is the partial pressure of each gass componet at 25 degrees?
What ways did sherman alexie facilitate own literacy : In what ways did Sherman Alexie facilitate his own literacy? Who and what aided Sherman Alexie's literacy?
Compute what is the resistance of the wire : The magnetic flux that passes through one turn of a 18-turn coil of wire changes to 2.62 from 9.44 Wb in a time of 0.0336s. What is the resistance of the wire

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the stationing of the pt on the same highway

A crest vertical vurve and a horizontal curve on the same highway have the same design speed. The equal-tangent vertical curve connects a +3% initial grade with a +1% final grade and has a PVC at 101+78 and a PVT at 106+72

  Calculate the normal strain using poissons ratio

If the normal stress is 2,500 psi, Poisson's ratio is 0.25 and Young's modulus is 10,000 ksi, calculate the normal strain.

  Calculate the head loss in 500 m of pipe

Carbon dioxide flows in a 75 mm diameter PVC pipe at 0.014 kg/s at a pressure of 345 kN/m^2/s abs and a temperature of 10 degrees C. Calculate the head loss in 500 m of pipe.

  How long must diameter be for mallet to balance at a point 6

A wood mallet has a cylindrical head 6 inches long and 3 inches in diameter. If the cylindrical head is 1 inch in diameter how long must it be for the mallet to balance at a point 6 inches from where the handle enters the mallet

  Make reasonable assumptions as to the soil properties

Soil borings made at a site near Chicago indicate that the top 6m is lose and miscellaneous fill, with the groundwater table at 3m below the ground surface. Below this is a fairly soft blue-gray silty clay with an average water content of 30%. The bo..

  Determine the height of the step on the floor

A uniform flow of normal depth 6 ft is developed upstream in a rectangular channel 10 ft wideand laid on a slope of 0.004. The Manning's coefficient n is given as 0.0149. There is a smooth step on the floor.

  Determine the amount of cover over a culvert

A vertical curve of 600 ft in length is used to connect two tangents with the following locations: Tangent 1.- Point 1, Sta = 59+00, El = 1250.0' Point 2, Sta = 72+00, El = 1190.0' Tangent 2.- Point 1, Sta = 72+00, El = 1190.0' Point 2, Sta = 84+0..

  What depth of aggregate is needed if angle theta is 40degree

A 2000-lb wheel load is to be supported by aggregate over soil with a maximum bearing pressure of 1000 lb/sqft. What depth of aggregate is needed if the angle theta is 40 degrees

  Determine horizontal distance the shot travels form a point

When the athlete releases the shot it is 1.82m above the ground and its initial velocity=13.6 m/s. Determine the horizontal distance the shot travels form the point of release to the point where it hits the ground.

  What percent of the particles does the settling tank capture

The setting velocity of a particle is 0.002 m/s and the overflow rate of a settling tank is 0.008 m/s. (a) what percent of the particles does the settling tank capture. If the particles are flocculated so that thie rsettling rate is 0.05 m/s

  What is the friction force under block b when this occurs

Two blocks A and B have a weight of 10 and 5 , respectively. They are resting on the incline for which the coefficients of static friction are = 0.15 and = 0.40. The spring has a stiffness of = 7 and is originally unstretched.

  What is value of p that make work of the two processes

If this two-step process is replaced by a single isothermal expansion of the air from 800 K and 4 bar to some final pressure P, what is the value of P that make the work of the two processes the same

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd