Determine the compressibility chart and amagat''s law

Assignment Help Civil Engineering
Reference no: EM131034205

A volume of 0.3 m3 of O2 at 200 K and 8 MPa is mixed with 0.5 m3 of N2 at the same temperature and pressure, forming a mixture at 200 K and 8 MPa. Determine the volume of the mixture, using (a) the ideal-gas equation of state, (b) Kay's rule, and (c) the compressibility chart and Amagat's law.

Reference no: EM131034205

Questions Cloud

How is the p-v-t behavior of a component in an ideal-gas : How is the P-v-T behavior of a component in an ideal-gas mixture expressed? How is the P-v-T behavior of a component in a real-gas mixture expressed?
Abrogation of the academics duty : Do you think that this represents an abrogation of the academics duty to serve the community that supports them - reports generated in accordance with accounting standards?
Which component will have the higher partial pressure : In a gas mixture, which component will have the higher partial pressure-the one with the higher mole number or the one with the larger molar mass?
How derivative products enhances the efficiency : Discuss how derivative products enhances the efficiency of the financial market in the respective countries. (Please note that your discussion should take into consideration of implication of at least one of the country's specific factor)
Determine the compressibility chart and amagat''s law : A volume of 0.3 m3 of O2 at 200 K and 8 MPa is mixed with 0.5 m3 of N2 at the same temperature and pressure, forming a mixture at 200 K and 8 MPa.
Determine the mass fraction and partial pressure of each gas : A gas mixture at 350 K and 300 kPa has the following volumetric analysis: 65 percent N2, 20 percent O2, and 15 percent CO2. Determine the mass fraction and partial pressure of each gas.
Give the editorial a catchy title and state your position : A letter to the editor is a briefly stated opinion generally written in response to a current issue or previously published article. It is typically very short-250-300 words. The purpose is to raise awareness of an issue, persuade people to thin..
Effects of various irrigation techniques on wheat production : Topic : effects of various irrigation techniques on wheat production. Preparation for the task The task in this assessment is to define a 'research problem' and conduct a 'review of theory' to support your research topic
Professional standards and regulatory requirements : Define actual and perceived independence, and explain the importance of each - discuss possible alternative courses of action the auditor should have taken in order to properly discharge their professional responsibilities

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find what is the unit price at the point of optimal demand

A large company in the communication and publishing industry has quantified the relationship between the price of one of itsproducts and the demand for this product as Price = 150- 0.01 x Demand for an annual printing of this particular product.

  Determine the normal depth and the froude number

A trapezoidal channel lined with d50 = 10 cm has a bottom width of b = 1.2 m, side slopes of m = 3, and a longitudinal bottom slope of S0 = 0.008. Determine the normal depth and the Froude number for Q = 1.4 m3/s.

  Draw shear force diagram for the beam

Calculate the support reaction at B and E and demonstrate the independent check used to ensure your calculated values are correct - Draw shear force diagram for the above beam approximately to scale showing all values at points A, B, C, D and E.

  Measure the performance of the case-study

Literature review; to define the criteria required to measure performance of the case- study and identifying the case-study , introducing the case-study and find relevant information.

  Find the value of the angle at which the projectile is fired

A projectile is fired with an initial velocity of 800 ft/s at a target B located 2000 feet above the gun A and at a horizontal distance of 12,000 feet. Neglecting air resistance, determine the value of the angle at which the projectile is fired.

  Determine the compressive buckling load

Two L 127 x 76 x 12.7-mm structural steel angles are used for a column (Use appendix B of the text book for cross-sectional properties) are used for a pin-ended column that is 4 m long. Determine the compressive buckling load if: θ· The angles act..

  Determine the ratio of the weight of the solid shaft

Two shafts are made of the same material and are of equal lengths.one of them is solid and another one is hollow. the ratio ofinside and outside diameters for hollow shaft is 0.65. They are subjected to the same torque and same maximum shearstress. D..

  Determine the runoff hydrograph that would be generated

Determine the runoff hydrograph that would be generated by a design 3-hr storm that generates excess rainfall at a constant rate of 10 mm/hr. assume baseflow is constant at 1.0 m3/s.

  You have been selected to assist the structural engineer

you have been selected to assist the structural engineer for a bridge replacement project. your task is to design the

  Find the minimum required depth d for a safe design

Shear and Bending Moment Diagrams - Find the minimum required depth ‘d' for a safe design. What is the maximum shear stress for this ‘d' value and where in the beam does it occur?

  The united states department of energy

Program developed by the United States Department of Energy (DOE) and the United States Environmental Protection Agency (EPA) to help reduce the amount of electricity used by computers and related devices

  Find percentage of air voids and voids in mineral aggregates

Find the percentage of Air voids and voids in the mineral aggregate if the asphalt absorption is .5%, and the specific gravities of the aggregate and binder are 2.660 and 1.020 respectively. The unit weight of the mixture is 2.39 Mg/m^3

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd