Determine the components of displacement at 1

Assignment Help Civil Engineering
Reference no: EM13320209

Determine the components of displacement at 1. Take E = 200 GPa, I = 250(10^6) mm^4, A = 12(10^3) mm^2 for each member.

Reference no: EM13320209

Questions Cloud

Evaluate the ph of the solution that results mixtures : Calculate the pH of the solution that results from each of the following mixtures. a)140.0 mL of 0.26M HF with 230.0mL of 0.32M NaF b)185 mL of 0.12M C2H5NH2 with 265mL of 0.20M C2H5NH3Cl
Calculate the maximum kinetic energy of electrons : Calculate the maximum KE of electrons emitted from a photo surface of work function 3.2 ev for the incident radiation of wavelength 300 nm
Lehman corporation purchased a machine : Lehman Corporation purchased a machine on January 2, 2011, for $2,000,000. The machine has an estimated 5-year life with no salvage value.
Calculate torque that must be applied to prevent : If N= 200, r = 5 cm, I = 2.5 A, B = 0.25 T Plane of coil makes an angle of 60 degree, with field line. Calculate torque that must be applied to prevent
Determine the components of displacement at 1 : Determine the components of displacement at 1. Take E = 200 GPa, I = 250(10^6) mm^4, A = 12(10^3) mm^2 for each member.
The amount charged to warranty expense : Kessler estimates its annual warranty expense as a percentage of sales. The amount charged to warranty expense on its books was $105,000. Assuming a 40% income tax rate, what amount was actually paid this year for warranty claims?
Determine the ratio of their activities at this instant : Two different elements with half lives Ta and Tb have Na & Nb (undecayed) atoms respectively, Determine the ratio of their activities at this instant
Iterative and incremental developments : Iterative and Incremental developments: focusing on unified Software
Calculate energy loss and approximate dimension of the jump : A wide rectangular channel has a change of slope from 1 in 100 to 1 in 500 and the flow is 4m3/s/m. Manning's n can be taken as 0.015 Determine the normal depth of flow before and after the change in gradient.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the maximum stress on the beam

draw shear and bending moment diagrams determine the maximum stress on the beam (E=2.0E+11Pa) a simply supported beam AB is 5 m long carrying a uniform distributed load of 10kn/m over a 4m span

  Determine who is at fault for the component failure

manufacturing process that unintentionally introduces cracks to the surface of a part was used to produce load-bearing components. The design requires that the component be able to withstand a stress of 450 MPa.

  What average speed will b have to mantain to overtake a

vehicle A enters the interstate and travel at 60 mph for 1/2 hour, stops for 30 mins then continues at 70 mph. If a vehicle B enters the interstate at the same location as A,

  Determine the drag coefficient for the sign type

The pressure on the back side is negative; its magnitude is 0.5 times the (negative) stagnation pressure on the back side. Determine the drag coefficient for the sign type

  Pressure on the soil if theta is given

A pipe is to be installed under the ground on a bed of aggregate 6 in. thick. The entire weight on the aggregate from pipe and soil above the pipe is 1800 lbs. per linear foot of pipe. What is the pressure on the soil if theta is 45 degrees? Assum..

  Determine the trade off between the cost and the head loss

The headloss per meter for galvanized iron pipe (.02 m diameter) hL= 0.110m and for (0.15m diameter) hL= 0.490m. Determine the trade off between the cost and the head loss (hL).

  Find what combinations of loads produce the max shear

beam is fixed at one end, spans 21' then goes over a roller support then 6' continues to hang over. there is a point load halfway betwen the supports (10.5') and another at the far end. there is also a distributed load that stretches the entire be..

  Compute the coefficient of roughness with a bottom width

A trapezoidal canal with a bottom width of 2 m, a side slope Z=1.5, and a longitudinal slope of 0.0006 conveys a flow rate of 3 m^3/s. If the water depth in section 1 is 0.78 m and in section 2

  How many kg per day of naoh must be added to neutralize

How many kg/day of NaOH must be added to neutralize a waste stream generated by an industry producing 90.8 million g/day of sulfuric acid, if 0.1% of the sulfuric acid produced is lost to wastewater The wastewater flow is 750,000 L/day

  Determine what is the unit discharge at 20 minutes

Assume a time to peak of 15 minutes and the unit peak discharge is 7.0 cfs/in, using the Gamma Function Unit Hydrograph what is the unit discharge at 20 minutes

  Determine the minimum elevation difference across channel

A 2 m diameter semicircular channel made of brickwork is to transport water to a distance of 1.7 km uniformly. If the flow rate is to reach 200 m3/min when the channel is full, determine the minimum elevation difference across the channel.

  Determine moment of inertia of beams cross-sectional area

Determine the moment of inertia of the beam's cross-sectional area about the x-axis. Set a = 40mm , b = 130mm , d = 110mm , h = 380mm .

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd