Determine the component v0

Assignment Help Civil Engineering
Reference no: EM131116829

The center of mass G of a high jumper follows the trajectory shown. Determine the component v0, measured in the vertical plane of the figure, of his takeoff velocity and angle ? if the apex of the trajectory just clears the bar at A. (In general, must the mass center G of the jumper clear the bar during a successful jump?)

335_3e7fb0f6-fc99-4710-9421-c4d3e119c9fd.png

Reference no: EM131116829

Questions Cloud

We need training course on time management : A manager says, “We need a training course on time management. We have 30 field representatives coming in for a conference next week and only 20% of them are actually meeting their goals. This is disappointing because they had the training four month..
Some customers become discouraged and leave : Create a process chart/flow chart to map the process of taking a license plate at Department of Motor Vehicle. Here are the process details: You enter the office and take a number, then walk 50 feet to the waiting area. During the wait, you count add..
Summarize the procedures that you used in the lab : A hypothesis is an educated guess. Based on what you have learned and written about in the Introduction, state what you expect to bSummarize the procedures that you used in the lab. The Methods section should also state clearly how data (numbers) w..
Divergence between marginal private costs : Air pollution from automobiles is an example of an externality, which means that there is a divergence between marginal private costs and marginal social costs.
Determine the component v0 : if the apex of the trajectory just clears the bar at A. (In general, must the mass center G of the jumper clear the bar during a successful jump?)
Calculate accounting profit and economic profit : Suppose that a business incurred implicit cost of $200,000 and explicit cost of $1million in a specific year.if the firm sold 4,000 units utput at $300 per unit, calculate accounting profit and economic profit.
Distinguish between short- run and long-run production : Distinguish between short- run and long-run production decisions and illustrate their impact on costs and economies of scale.
What is the net revenue per patient : Using the Patient Cost Analysis Form in the Appendix from your "Revenue Management Manual" text (Form A26), calculate your current costs per patient using the following information. What is the Net Revenue per patient?
Examine the effect on market power : The supply of oil is heavily influenced by the decisions of oil-rich countries such as Saudi Arabia and Kuwait. Producers with market power tend to restrict supply to force prices up. Examine the effect on this market power.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the maximum allowable load pallow

A rigid steel plate is supported by three posts of high-strength concrete each having an effective cross-sectional area A=40,000 mm^2 Determine the maximum allowable load Pallow

  Calculate the uniform flow depth in the channel at flow rate

Water flows i a 8-m-wide rectangular channel that has longitudinal slope of .0001. The channel has an equivalent sand roughness of 2mm. Calculate the uniform flow depth in the channel when the flow rate is 15m^3/s. Use the Darcey-Weisbach equation..

  Does the steel have adequate charpy v notch fracture tough

A Charpy V Notch test was conducted for an ASTM A572 Grade 50 bridge steel. the average values of the test results at four different test temperatires were found to be 10ft.lb -(-50 F) 15 ft.lb- 0F 40 ft.lb- 40F 60 ft.lb-100 F

  Compute the do and initial ultimate bod after mixing

The wastewater treatment plant for Pine City discharges 1 × 105 m3/day of treated waste to the Pine River. Immediately upstream of the treatment plant, the Pine River has an ultimate CBOD of 2 mg/L and a flow of 9 × 105 m3/day.

  Write an expression that executes the exclu() memberfunction

write an expression that executes the exclu() member function in this object.

  Determine the total force needed to overcome axle friction

A 100-ton train traveling on a horizontal track requires 400 hp to maintain a constant speed of 50 mi/h. Determine (a) the total force needed to overcome axle friction, rolling resistance, and air resistance

  What is the largest number of phases that can coexist

Considering both temperature and pressure to be variables, what is the largest number of phases that can coexist at equilibrium in a binary alloy

  Determine what is the magnitude and direction of the force

what is the magnitude and direction of the force of the water n the nozzle, if the nozzle is held steady/2- what is the FORCE if the fire fighter is running towards the fire, with the hose at a velocity of 1.5 m/s

  What is its speed at the point that the force resisting

This problem models an insertion process. Block A (mA = 2kg) is acted on by a horizontal force F (F = 12 N). As A moves to the right, it gets pressed more and more tightly in the channel.

  Magnitude of the maximum compressive bending stress

Find the magnitude of the maximum compressive bending stress and also the magnitude of the maximum tensile bending stress

  What is the cubic feet of gas storage space in fault block

After injecting 50 MMSCF (14.7 psia and 60 oF), the pressure increase from 2500 to 3500 psia. Deviation factors for the gas are 0.90 at 3500 and 0.80 at 2500 psia and the bottom-hole temperature is 160 oF. What is the cubic feet of gas storage spa..

  Selecting the site for hydroelectric power plant

Describe brefly different factors to be considered while selecting the site for hydroelectric power plant.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd