Determine the coliform concentration at the beach

Assignment Help Civil Engineering
Reference no: EM13545661

An ocean outfall diffuser that discharges treated wastewater into the Indian Ocean is 5,000 m from a public beach. The wastewater contains 105 coliform bacteria per milliliter. The wastewater discharge flow rate is 0.3 m3/s. The coliform first-order death rate in seawater is approximated 0.3 h-1. The current carries the wastewater plume toward the beach at a rate of 0.5 m/s. The ocean current may be approximated as a pipe carrying 600 m3/s of seawater. Assume that the current behaves as a plug-flow reactor and that the wastewater is completely mixed in the current at the discharge point.

Determine the coliform concentration at the beach. (assume that the current behaves as a plug flow reactor and that the wastewater is completely mixed in the current at the discharge point.

Reference no: EM13545661

Questions Cloud

Will the quantity of coarse aggregate incease decrease : A concrete mix with a 3in slump, w/c ratio of .5, and sand with a fineness modulus of 2.4 contains 1700lb/yd3 of coarse aggregate. Compute the required weight of coarse aggregate per cubic yard.
How you will place the bars and calculate the location : Concrete cover on both sides. Sketch how you will place the bars and calculate the location of the effective depth. Place as many bars in the lower layers as possible.
How many cubic yards of aggregate must be ordered for a road : How many cubic yards of aggregate must be ordered for a road base 16 inches thick and 2000 feet long with a top width of 30 ft, if the side slopes are one on one, or 45 degree?
What major differences would you expect if the water supply : A large stream flowing through a highly industrialized area must serve as the source of a community's water supply. The turbidity of the water ranges from 30 to 60 NTU, alkalinity exceeds 100 mg/L.
Determine the coliform concentration at the beach : Determine the coliform concentration at the beach. (assume that the current behaves as a plug flow reactor and that the wastewater is completely mixed in the current at the discharge point.
What is the discharge of each hole : A water of 20 c temprature pupped at 75 kpa to a perforated pipe 5 cm dia. contain 10 hole with the same diameter. the distance between two adjacent hole is 20 cm. what is the discharge of each hole?
Use the conveyance method to verify the results : A drainage channel had a cross section that may be approximated as a trapezoidal section with a bottom width of 15 feet and a side slope of 1.5H:1V. If the channel drops 2.5 feet per mile.
Determine the size of the watershed in acres and then : The 1-hr UH in the table was recorded for a particular watershed. Determine the size of the watershed in acres and then convert the 1-hr UH into a 3-hr UH for the watershed.
Determine the magnitude of the largest elastic load p that : The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. the outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. if the yield stress for the steel is

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the magnitude of the load p

A round bar of 6mm diameter is made of 6061-T6 aluminum. When the bar is stretched by an axial force P, its diameter decreases by 0.450 microns. what is the magnitude of the load P

  Determine the mass nd specific volume of argon gas in vessel

Determine the mass and specific volume of argon gas in a vessel at 150 kPa and 20°C. The vessel is spherical, with radius 5 m.

  Determine time of queue dissipation and longest queue length

Finally, the wreckage is removed, and the freeway is restored to full capacity (4000 veh/h) at 8:31 a,. Assume D/D/1 queuing to determine time of queue dissipation, longest queue length, total delay, average delay per vehicle, and longest wait of ..

  How much can the company afford to spend per month

Wheeling-Pittsburgh Steel is investigating whether it should it should replace some of the basic oxygen furnace equipment now or wait to do it later. The cost later (i.e. 3 years from now) is estimated to be $1,700,000.

  Determine the sludge age and cell wastage flow rate

Assume: Suspended solids in effluent negligible Wastage is from aeration tank Yield coefficient = 0.4 Bacterial decay rate = 0.04 1/d Effluent BOD5 = 10mg/L F/M = 0.33 mg/mg*d BOD5 after primary settling = 150mg/L MLVSS = 1700mg/L MLSS = 1.4(MLVSS..

  What is the min length for the off-ramp to provide storage

If the average length of a vehicle is 15 ft and the average space between consecutive vehicles waiting to be served is 3 ft, what is the minimum length for the off-ramp to provide storage for all exiting vehicles 80 percent of the time

  What is the distribution reinforcement percentage of area

What is the Distribution reinforcement percentage of area ? Hot to take it for the calculation of distribution reinforcement in dog-legged stair case.

  What would be the capillary pressure between oil and water

If the interfacial tension between air-mercury interface in a capillary tube is 480 dynes/cm and the contact angle through the mercury is 140, what would be the capillary pressure between oil and water

  Compute the geodetic coordinates of the station qbn from

Compute the geodetic coordinates of the station QBN from station MDU If coordinates of station MDU are f = 39°51'55"N, ? = 104°40'58"W Distance = 30km, Az = 243°40'48”, h = 1850m, dh= -20. Ellipsoid GRS80

  How to design for a cultivated land with sandy loam soil

The bund channel is to be formed by the embankment only. The horizontal distance between two bund s is 50 m. The 1-hr rainfall expected during the recurrence interval of 10 yrs is 8 cm/hr.

  What must be the density of the gas at that section

Gas flows at a steady rate in a 120-mm-diameter pipe that enlarges to a 180-mm-diameter pipe. At a certain section of the 120-mm pipe the density of the gas is 165 kg/m^3 and the velocity is 15 m/s.

  Determining height for trajectory motion

The elastic ball bounces down a flight of rigid stairs. Determine the height h of the steps if all the trajectories between successive steps are identical. Use e = 0.85 and the initial velocity 6 m/s.neglect friction. (Theta=70 degrees)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd