Determine the coil load circulation and ventilation airflow

Assignment Help Mechanical Engineering
Reference no: EM131240627

Determine the coil load, circulation and ventilation airflow rates, and thermodynamic states for a CAV system at design conditions for a commercial office building. The design ambient conditions are 92 F dry bulb and 78 F wet bulb. The building can be treated as a single zone with a total zone load of 500,000 Btu/hr and a sensible heat ratio of 0.8. The design occupancy is 80 people and the corresponding ventilation air flow rate is 1600 cfm, which is based on 20 cfm of outdoor air per person. The zone temperature thermostat setting is 77 F, which is within the summer comfort zone. The bypass factor for the coil is 0.175 and the chilled water temperature is 50 F.

Reference no: EM131240627

Questions Cloud

Determine the incidence that corresponds to the blade : determine the incidence that corresponds to the blade stalling.b. Use Carter's deviation correlation to estimate the required metal exit angle given that aparabolic arc camber line is employed with maximum camber at 40% chord. (Note thatsome itera..
About the income-price-level and expected-inflation effects : M1 money growth in the U.S. was about 15% in 2011 and 2012, and 10% in 2013. Over the same time period, the yield on 3-month Treasury bills was close to 0%. Given these high rates of money growth, why did interest rates stay so low, rather than incre..
Private ownership in the market system : Private ownership in the market system is believed to enhance innovation and faster growth than in the command economic system. With examples, explain why or why not this statement is true.
Savings account paying nominal annual interest : Bart wishes to tour the country with his friends. To do this, he is saving money for a bus. How much money must Bart deposit in a savings account paying 8% nominal annual interest, compounded continuously, in order to have $8,000 in 4.5 years?
Determine the coil load circulation and ventilation airflow : The zone temperature thermostat setting is 77 F, which is within the summer comfort zone. The bypass factor for the coil is 0.175 and the chilled water temperature is 50 F.
Estimate the minimum fluidization velocity : Estimate the entrainment velocity. Hint: The entrainment velocity for a sphere is equal to its settling velocity. [m/s] Approx. answer: 0.01 m/s
Would this company run the business under this regulation : Consider a subway company whose cost function is given by C(T) = 1000 +T. Due to the government regulation, this company must set the fare per passenger at the marginal cost (MC pricing). Is this pricing efficient? Would this company run the business..
Utility function-consumer surplus : Zhou has a utility function given by U=X1X2X3 , where X1 is cups of soda consumed per month, X2 is pizza consumed per month and X3 is hamburgers consumed per month. Derive Zhou’s Marshallian demand functions for soda, pizza and hamburger.
What is the specific heat of aluminum : what is the specific heat of aluminum if the temperature of a 28.4 g sample of aluminum is increased by 8.1 degrees celcius when 207 J of heat is added

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Coefficient of friction between the pin and surface of hole

Determine the coefficient of friction between the pin and the surface of the hole. normal to the tapered pin surface remains unchanged until the pin actually moves.

  A carnot cycle heat engine using 1 kg of air has the

a carnot cycle heat engine using 1 kg of air has the following conditions heat addition beginning at 15 mpa and 1200 k

  What is the ratio of the flowrates through the straws

what is the ratio of the flowrates through the straws? Assume the drink is viscous enough to ensure laminar flow and neglect gravity.

  Temperature measurement device is calibrated to produce

A temperature measurement device is calibrated to produce 4-20 mA for a temperature operation range of 0-100 degree C. Sketch the input-output characteristic chart of the device, assuming linear input/output relationship.

  Water flows at 50oc inside a 25-cm-inside-diameter tube

1.water flows at 50oc inside a 2.5-cm-inside-diameter tube such that hi 3500 wm2 oc. the tube has a wall thickness of

  A 50 lb weight is attached to the end of a 10 inch long

a 50 lb. weight is attached to the end of a 10 inch long beam e30106 psi which is 1 inch wide and 14 and inch deep and

  Determine the magnitude and direction of the force

Determine the magnitude and direction of the force P.

  Determine the surface temperature of the heated panel

A room has 1000 ft2 of surface, of which 120 ft2 is to be heated, and the balance has an average surface temperature of 60°F. The air temperature in the room is 68°F. The room is occupied by light clothed adults at rest. Determine the surface tempera..

  Volume of second tank and final equilibrium pressure of air

A 1-m tank contains air at 10oC and 350 kPa is connected through a valve to another tank containing 3 kg of air at 35oC and 200 kPa. Now the valve is opened, and the entire system is allowed to reach thermal equilibrium with the surroundings, which i..

  Find the power required for the cut in kw

In a turning operation the feed rate t is .13 mm (.005 in.) and the depth of cut normal to the plane of the paper is 2.5mm (.100 in). The cutting speed is 245 m/min (800 fpm). The cutting force F_c is found to be 1780N (400lb) and the normal force F_..

  The cross sectional area is 05 cm2 and is of length 50 cm

a cylindrical rod of an unknown material is subject to a force of 20000n. the cross sectional area is 0.5 cm2 and is of

  The simple steam power cycle in prob 423 in modified in the

the simple steam power cycle in prob 4.23 in modified in the following way. steam entering the turbine is expanded to

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd