User Account

All Pages

Determine the circumferential stresses

Assignment Help Mechanical Engineering
Reference no: EM131590242

Question 1. The asymmetric I-beam shown is made of A992 Gr. 50 steel (fy = 50 ksi).

1230_Figure1.jpg

a. Assuming Elastic-Perfectly Plastic behavior and the same properties in tension and compression, determine the fully plastic moment.

b. If the beam is curved and subjected to the uniform moment, M, shown below. Determine the circumferential stresses (σθθ) in the beam at points A and B.

753_Figure2.jpg

Question 2. The non-symmetric aluminum (E = 70 GPa) channel section shown is used as a simply-supported beam spanning 3 m that must support a vertical load of 800 N (Φ = 90°) at the center of the beam. The maximum moment for this span configuration is M = 600 N-m and is directed as shown on the cross-section. The beam section properties are given below the figure.

2248_Figure3.jpg

a. Determine the principal moments of inertia, Imax and Imin, and the orientation of the principal axes, θp.
b. Determine the orientation of the neutral axis, α.
c. Determine the maximum tensile and the maximum compressive stresses in the beam.

Question 3. A fabrication error resulted in an I-beam with an off-center web causing the shear center to no longer be located at the centroid of the web. The cross-section of the I-beam is shown. Because the I-beam still has one axis of symmetry, the x- and y-axes are principal axes. Therefore, when a vertical shear force, V, is applied, the x-axis is the neutral axis.

1455_Figure4.jpg

a. For a vertical shear force of V = 1 kN, determine the shear flow distribution in each segment of the beam. Also, determine the total shear force in each segment of the beam clearly showing the direction of the resultant shear force in each section.

b. Determine the location of the shear center with respect to the centroid of the web, e, for the beam. You should use your results from part a to locate the shear center and verify this result by calculating the location of the shear center using the correct equation from Table 8.1 in the textbook (slides 12 and 13 in lecture 8b).

Question 4. A large crane is supported on steel (E = 29,000 ksi) rails on an elastic foundation. Each wheel carries a load of 100 kip. The steel rails are 6 in. wide at the base, have a moment of inertia of I = 1,200 in4 and a section modulus of S = 130 in3. The elastic foundation consists of concrete sleepers over a thick gravel base over soil which results in an effective spring constant of k0 = 300 psi/in.

a. Determine the maximum displacement of the rail, maximum moment in the rail, and maximum normal stress in the rail due to a single wheel load if the rail and elastic foundation can be considered to be infinite.

b. Determine the maximum displacement of the rail, maximum moment in the rail, and maximum normal stress in the rail, when a single wheel load is placed at the end of a semi-infinite rail.

c. If the foundation is to be modeled with discrete springs, determine the minimum spacing of the discrete springs necessary for "reasonable" results. Also, determine the spring constant, K, that should be used for each discrete spring.

Verified Expert

This problem has been solved as per the behavior of material under given condition. The problem has been solved by using advance mechanics of solid of material properties. The aim of the problem solved for obtain stress under different applied load. The problem is consider by using standard section which is used in analytical method. The problem has been prepare with analytical method to obtain solution.

Reference no: EM131590242

Questions Cloud

Create presentation organize indicated in note from samantha : Based on the Word file provided, create a six to eight slide presentation organized as indicated in the note from Samantha.
Why is quickbooks a better option than a manual accounting : Why is QuickBooks a better option than a manual accounting process when it comes to dealing with vendors and customers
Create naming conventions for each entity and attributes : A multinational tour operator agency has gained new business growth in the North American market through the use of social media.
What one issue do you think churches should address today : Do you think churches have done enough with regard to social inequality, poverty, injustice, and so on
Determine the circumferential stresses : Determine the circumferential stresses in the beam at points A and B - Determine the orientation of the neutral axis
Compute the equivalent units of production for materials : Compute the equivalent units of production for (a) materials and (b) conversion costs for the month of November
Are you getting the message : Discuss these two (2) examples of message appeals in your blog post. Provide a detailed description,& judge whether the appeals are effective for that product.
Name three tools available for threat modeling : Which one of these tools would you recommend and why?
Why is the customer interview process important : Why is the customer interview process important with regard to the Chart of Accounts (COA)? Why would you customize a COA to a specific business

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A cylindrical specimen of a metal alloy

A cylindrical specimen of a metal alloy 51.3 mm long and 11.1 mm in diameter is stressed in tension. A true stress of 350 MPa causes the specimen to plastically elongate to a length of 57.9 mm. If it is known that the strain-hardening exponent for th..

  How much heat is rejected to the cooling system

steam with 88.6% quality and a flow rate of 750 kg/s enters a condenser operating @ 75 KPa. Saturated liquid leaves the condenser. How much heat is rejected to the cooling system.

  If its initial velocity is 63 ms what is its displacement

an object moves with constant acceleration 4.20 ms2 and over a time interval reaches a final velocity of 12.6 ms. a if

  Measures a wind tunnels velocity n times

During an experiment, an aerospace engineering student measures a wind tunnel's velocity N times. The student reports the following information, based on 90% confidence, about the finite data set: mean velocity=25 m/s, velocity standard deviation=1.5..

  The tank is not very well insulated after many hours the

a rigid tank is filled with refrigerant r-134a at 310 k. an electric current of 0.2 amps over 220 volts is passed

  Conduction limit of heat transfer

If the fluid around the sphere is quiescent and extensive, show that the conduction limit of heat transfer from the sphere can be expressed as NuD, cond = 2.

  A steam turbine produces 3000 hp with a mass flow rate of

a steam turbine produces 3000 hp with a mass flow rate of 22000 pounds per hour. the steam enters at 1100 degf and 900

  Before entering the furnace the air is preheated from 32f

propane is to be burned with 15.0 excess air. before entering the furnace the air is preheated from 32f to 575f. at

  Fundamental principles and constitutive relations

Fundamental principles and constitutive relations Problem 1.) Shortly after you light a candle, the flame reaches the melting temperature (To). It has an initial length of Lo that will decrease while melting. There is a net heat flux qo to the top su..

  Find apsidal angle for a nearly circular orbit of radius a

Find the apsidal angle for a nearly circular orbit of radius a. When ∈ is small, show that the perihelion of the orbit advances by approximately π? on each revolution.

  Block of copper at initial temperature

A 25-kg block of copper at initial temperature of 1500C equilibrates with 0.79 kg of liquid water at an initial temperature of 200C in an insulated tank. If the average specific heat of copper can be taken to be 0.395 kJ/kg.K, determine the final tem..

  Duct flow is modeled by steady dimensional velocity field

Converging duct flow is modeled by the steady two-dimensional velocity field. For the case in which Uo = 3.56 ft/s and b = 7.66s^-1, Plot several streamlines from x = 0 to 5 ft and y = -2 to 2 ft. Be sure to show the direction of the streamlines.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd