Determine the channel height that can be used to determine

Assignment Help Mechanical Engineering
Reference no: EM13614043

A) For a rectangular coordinate system, we developed the Navier Stokes equation for vx. Now, reduce that equation to balance the pressure force with shear stress (or frictional force) and develop an expression for vx in a rectangular channel of height h (y=0 is the centerline and no slip at y= +- h/2; use the concept of symmetry). Then develop an expression for vmax, average velocity, flow rate (Q) and shear stress at the wall (For flow rate calculations, assume a width of the channel to be w. Therefore the cross sectional area of the channel is wh).

B) Design of a chamber that will be used to study cell culture under a flow field: Determine the channel height that can be used to determine the wall shear stresses as high as 20 dyne/cm2 with flow rates less than 2 cm3/s. The viscosity of the tissue culture medium is 0.0087 gm/cm.s. The width of the channel is 2 cm

Reference no: EM13614043

Questions Cloud

The thoughts that ted presented which were about shifting : i. choose the correct sentence.with triplets i have to be careful to divide everythingequally among them or they will
Two balls 14 cm in diameter are placed 200 m apart on a : two balls 14 cm in diameter are placed 200 m apart on a frictionless horizontal plane at 50ordm n on the rotating
What is the outlet pressure if the inlet pressure is 100 mm : for a one order narrowing of arterial vessel in cross sectional area ainaout 10 what is the outlet pressure if the
What information does franks current accounting system : for about a year frank poppa has been operating a hot dog standin the parking lot of a major discount retailer in a
Determine the channel height that can be used to determine : a for a rectangular coordinate system we developed the navier stokes equation for vx. now reduce that equation to
Bob can afford monthly car payments of 200 for four years : bob can afford monthly car payments of 200 for four years. what is the most expensive car bob can buy if the
After six months of operation brothers lawn service hadthe : after six months of operation brothers lawn service hadthe following revenue and expense account
Show the cycle on a t-s diagram with respect to the : consider a 210mw steam power plant that operates on a simple rankine cycle. steam enters the turbine at 10mpa and 500oc
Kleener co acquired a new delivery truck at the beginning : kleener co acquired a new delivery truck at the beginning ofits current fiscal year. the truck cost 26000 and has an

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd