Determine the capitalized cost of the project

Assignment Help Civil Engineering
Reference no: EM13552842

The lubbock board of city development has decided to ask the city council to construct a tunnel under the snowcapped mountain range east to downtown lubbock so that out of town visitors can reach historic prairie dog town without becoming lost and ending up at the ski lift. This project is expected to have a first cost of $2,000,000 and an annual maintenance cost of $50,000. In addition, major repairs costing $250,000 will be required after 25 years and each 15 years thereafter. Use an interest rate of 12% and determine the capitalized cost of the project.

Reference no: EM13552842

Questions Cloud

The topic is the poisson distribution : The concentration of particles in a suspension is 4 per mL. The suspension is thoroughly agitated, and then 2mL is withdrawn. Let X represent the number of particles that are withdrawn.
Same proportion of buildings in the two cities : What is the probability that he will have the same proportion of buildings in the two cities?
What is the break-even number of units per year : Sled and rider with a total weight of 200 lb travel down smooth slope defined by equation y=x^2/20. At x=40 ft the sled's speed is 10 ft/s. At x=40 ft determine rate of increase of speed and the normal force which the slope exers on the sled. Neglect..
Compute the degree of the curve given the radius r : Compute the degree of the curve given the radius R as 1) R=300.00ft by arc definition 2) R=900.00 ft by chord definition
Determine the capitalized cost of the project : The lubbock board of city development has decided to ask the city council to construct a tunnel under the snowcapped mountain range east to downtown lubbock so that out of town visitors can reach historic prairie dog town without becoming lost and en..
Determine the final velocity of the carrier : A 30 g bullet is fired with a horizontal velocity of 450 m/s through 3-kg block B and becomes embedded in carrier C which has a mass of 30 kg. After the impact, block B slides 0.3m on C before coming to rest relative to the carrier.
Given the data below for two alternatives find the better : Given the data below for two alternatives, find the better alternative, if MARR is 8%. alt A |alt B Initial cost $10,000 |$15,000 maintenance cost/ year $1,000 |$500
Determine the most desirable alternative based on the result : Annual rare based on amount of products which can ordinarily be shipped each year as a function of the amount of vehicles or service purchased with the first cost and the M&O costs. Using a MARR of 15%, calculate the equivalent uniform annual cash fl..
What is the probability that the entire system is successful : In a support system in the U.S. space program, a single crucial component works only 85% of the time. In order to enhance the reliability of the system

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the difference in temperature form standard

A driver on a leveltwo-lane highway observes a truck completely blocking thehighway.The driver was able to stop her vehicle only 20 ft. fromthe truck. If the driver was driving at 60mph, how far was she fromthe truck when she first observed it?

  Find the concrete cross-section and steel area required

Find the concrete cross-section and steel area required for a simply supported rectangular beam with a span of 20 ft that is to carry a computed dead load of 1.3 k/ft and a service live load of 2.25 k/ft.

  A well hit golf ball travels at a speed of 150 mph

A well hit golf ball travels at a speed of 150 mph ( 220 ft/s) as it leaves the tee. The golf ball has a diameter of 1.70 in and weighs 0.099 lb. Assuming standard atmospheric conditions (mu, u air = 3.74 * 10^-7 lb-s/ft2 and rho = 0.00238 slug/ft3) ..

  Find channel cross section and the required channel slope

A rectangular channel is to carry 200 cfs. The mean velocity must be greater than 2.5 fps. The channel bottom width should be about twice the channel depth. Find the channel cross section and the required channel slope.

  Find coefficient of kinetic friction if car comes to stop

A classic car is d riving down an incline at 60 km / h when its brakes are applied. Treating the car as a particle, neglecting all forces except gravity and friction, and assuming that the tires slip

  What is max amount of benzene that the company can discharge

A company near City X want's to know how much benzene they can release into River Y. City Z is 85.5 miles downstream from City X. City Z doesn't want to have Benzene levels higher than 0.0000015 g/L.

  How much error would there be in the volume calculation

Assume the actual water temperature for calibrating a 1/3 ft3 measure was 65 degrees F. If you had used a water temperature of 75 degrees F for your calibration, how much error would there be in your volume calculation (both in ft3 and as a percen..

  What type of volcano is olympus mons

A-Olympus Mons, a 69,000-foot-tall mountain on Mars, is the largest volcano in the solar system. Its circumference at the base is large enough to cover almost the entire state of Colorado. A space probe could safely land at almost any point on the vo..

  How to determine the rating curve of the spillway

Consider a 75-ft wide overflow spillway with no piers and a design head of 18 ft. The crest elevation of the spillway is 2400 ft and the streambed elevation just upstream of the spillway is 2350 ft.

  Does our non-destructive test have the required sensitivity

To be sure that the part does not fail, we plan to ensure that the maximum applied stress is only one third of the tensile strength. We use a non-destructive test that will detect any internal flaws greater than 1.25 mm long.

  Determine pipe size required at ultimate development stage

The country town with service area of 150 ha is sewered, and the main outfall sewer is laid on a grade (slope) of 0.003 m/m to a treatment plant. Effluent from the treatment plant is at present discharged via an open channel to the river.

  Determine what was the major principal stress at failure

A consolidated-drained triaxial test on a normally consolidated clay yielded a friction angle of 28°. If the all-round confining pressure during the test was 140 kN/m2, what was the major principal stress at failure.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd