Determine the braking efficiency of car

Assignment Help Civil Engineering
Reference no: EM13544545

Two cars are traveling on level terrain at 60 mi/h on a road with a coefficient of adhesion of 0.8. The driver of car 1 has a 2.5-s perception/reaction time and the driver of car 2 has a 2.0-s perception/reaction time. Both cars are side by side and the drivers are able to stop their respective cars in the same amount of distance after first seeing a roadway obstacle (perception/reaction plus vehicle stopping distance). If the braking efficiency of car 2 is 0.75, determine the braking efficiency of car 1. (Assume minimum theoretical stopping distance and ignore aerodynamic resistance.)

Reference no: EM13544545

Questions Cloud

Determine the normal stresses induced in the steel and in : The concrete post (Ec=3.6*10^6 psi and Ac= 5.5*10^-6/degrees F) is reinforced with six steel bars. each of 7/8-in diameter (Es=29*10^6 psi and As=6.5*10-6/ degrees F).
Notch fracture toughness show your supportin calculations : A Charpy V Notch test was conducted for an ASTM A572 Grade 50 bridge steel. the average values of the test results at four different test temperatires were found to be
How far from shore is a sailboat when the top of its 8m : How was this answered reached? what equation was used? equation of a line? could you please explain how the answer was reached and a detailed explanation of the math behind it.
Determine the youngs modulus of the steel alloy and the : a round steel alloy bar with a diameter of 0.75 in and a gauge length of 3.0 in was subjected to tension, with the results shown in the accompanying table. using a computer spread sheet program
Determine the braking efficiency of car : Two cars are traveling on level terrain at 60 mi/h on a road with a coefficient of adhesion of 0.8. The driver of car 1 has a 2.5-s perception/reaction time and the driver of car 2 has a 2.0-s perception/reaction time
What is the shortest height it should be : An engineering student has been given the assignment of designing a hydraulic holding system for a hay baling system. The system has four cylinders with 120 mm diameter pistons with a stroke of 0.320 m
Select a hydraulic pump size and a hydraulic cylinder size : An engineer is designing a hydraulic lift with a capacity of 10 tons. the moving parts of this lift weigh 1000lbf. the lift should raise the load to a height of 6ft in 20 seconds. This will be accomplished with a hydraulic pump
The given data show the result of a model known : The given data show the result of a model known as stopping sight distance, used by civil engineers to design roadways speed(mph) stopping sight distance(ft)
Design and detail the steel reinforcement for the section : The beam has a rectangular section which is to be singly reinforced. Given pt=1.1% design and detail the steel reinforcement for the section where the moment is maximum

Reviews

Write a Review

Civil Engineering Questions & Answers

  Give the definition of relative density in term of void

Air flows into the atmosphere from a nozzle and strikes a vertical plate as shown in Fig. P5.28. A horizontal force of 9 N is required to hold the plate in place. Determine the reading on the pressure gage. Assume the flow to be incompressible and fr..

  What is the design storage and water surface elevation

What is the design storage and water surface elevation at the peak outflow rate and estimate the long-term average reduction (EPA, 1986) in particulates under dynamic conditions.

  Calculate the compacted cubic yards per hour over 10-inch

Calculate the compacted cubic yards per hour if a compactor with a 5-ft drum width travels at 3 mph over a 10-in. lift of aggregate base course with 4 passes required to meet density specifications under average operating conditions.

  Find reservoir in acre-ft that would be required to contain

A hurricane has an average rainfall of 9 in over a 200 mile^2 watershed. What is the reservoir in acre-ft that would be required to contain 20% of the rain completely

  Find what must the form of the velocity component v be

Three components of an incompressible flow field are given by u=a(x^2-y^2), v unknown, and w=b, where a and b are constants. What must the form of the velocity component v be

  What would be the co concentration in the box

GIVEN: A simple way to model air pollution over a city is with a box model that assumes complete mixing and limited capability for the pollution to disperse horizontally or vertically except in the direction of the prevailing winds (for example, a to..

  Determine the r-134a exit temperature in the enthalpy

At compressor exit, the specific entropy is the same as that at the inlet, and the pressure is 60 psia. Determine the R-134a exit temperature and the change in the enthalpy of R134a.

  What are the best dimensions for a trapezoidal canal having

What are the best dimensions for a trapezoidal canal having a side slopes of 1V : 3H and n = 0.020, if it is to carry 40 m^3/s uniformly on a slope of 0.009.

  Determine the average force exerted by the parachute

Modeling the skydiver as a particle and assuming that the skydiver follows a perfectly vertical trajectory, determine the average force exerted by the parachute from the moment of deployment until landing.

  Convert all quantities to si units then convert it to mph

Assume the plane is flying at an altitude of 32,810 ft (10 km), where the temperature is -8 C and the pressure is 250 mb. The Pitot-static tube measures a piezometric pressure difference corresponding to 1.206 psi. What is the airspeed in both m/s..

  Concrete dam retaining water

A concrete dam retaining water has a specific weight of concrete of 23.5kn/m3, what is the factor of safety against sliding & overturning and pressure intensity on the base if coefficient of friction is 0.45

  Determine the torsional moment in the hollow x-section

A concrete box girder bridge has the rectangular x-section. The box is prismatic and considered thin-walled. It span is L=48m and simply supported at points A,B,C and D. The supports are assume to be able to transfer tensile forces.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd