Determine the bounce angle and the group velocity v

Assignment Help Electrical Engineering
Reference no: EM13263857

Light of free-space wavelenth lambda_0= 0.87 micrometers is guided by a thin planar film of width d=2 micrometers and refractive index n_1=1.6 surrounded by a medium of refractive index n_2=1.4.

(a) Determine the critical angle and its complement, the numerical aperture NA, and the maximum acceptance angle for light originating in air (n=1).

(b)Determine the number of TE modes

(c) Determine the bounce angle and the group velocity v of the m=0 TE mode.

Reference no: EM13263857

Questions Cloud

What is number of modes if waveguide with thickness is used : What is the largest thickness d of a planar symmetric dielectric waveguide with refractive indexes n_1=1.50 n_2=1.46 for which there is only on TE mode at lambda_0=1.3 micrometers. What is the number of modes if a waveguide with this thickness is ..
Research question and hypothesis : Use the library, Internet, and other available resources to develop a 6–8 page research proposal that includes the following:Introduction to your topic "Police Discretion" and related issues (variables)
How far away from the battleship is the submarine : A battleship is using sonar (reflected underwater sound signals) to detect the presence of nearby submarines. How far away from the battleship is the submarine
Determine the bounce angle and the group velocity v : Light of free-space wavelenth lambda_0= 0.87 micrometers is guided by a thin planar film of width d=2 micrometers and refractive index n_1=1.6 surrounded by a medium of refractive index n_2=1.4.
Determine the value of the resistance of r : discharge a capacitor of 1mF charged with a voltage of 1 volt we connect it, at time t = 0, with a esistor of R ohm. When we measure the voltage we find it to be V(r) (t) = e ^(-t) u(t). Determine the resistance of R. If the capacitor has a capaci..
Determine what voltage value will be measured : We can model the human body as a voltage source in series with a high resistance, let's say 10mV in series with 100kOhms. If we use an instrument with 1MOhm input resistance, what voltage value will we measure
What is the value of trying new things : Explain how this was a new experience for you - Describe in detail your experience. Where did you go? What did you do? Who else went with you or who did you meet

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the source voltage of power transmission system

Determine the source voltage Vs of a 60-Hz power transmission system from the loading conditions described as follows: 1. The load is capacitive and absorbs 12 kW at 240

  What is qualitative difference in cmos nd non-cmos devices

Consider the current it takes to power a +5V 74xx245(Icc). What is the qualitative difference between the CMOS devices and the non-CMOS devices and the non-CMOS devices What is the explanation for the difference

  Determine the mid point of the voltage divider

An n-channel JFET needs a NEGATIVE voltage applied to its GATE, relative to its SOURCE. If you have a single POSITIVE supply applied to the MASTER loop of a JFET, the mid point of the voltage divider will also be a positive voltage

  What is the average current if the duty cycle is given

An H-bridge allows a 4 A current pulse to the drive motor. What is the average current if the duty cycle is 75% and the pulse frequency is 2 kHz

  Calculate current in incoming and outgoing transmission line

three single-phase transformers rated at 250kVa, 7200V/600, 50Hz, are connected in wye-delta on a 12470V, 3 phase line, if the load is 450kVA, calculate the current in the incoming and outgoing transmission lines and in the primary and secondary w..

  Define the outputs of two nand

Can you confirm-The outputs of two"NAND" gates are connected to the inputs of an "EXCLUSIVE OR" gate.Each of the "NAND" gates has one input at logic high level and the other input

  What is the actual value of the irr on the incremental cost

a) Construct a choice table for interest rates from 0% to 100%. b) Which roof should you choose if your MARR is 12% what is the actual value of the IRR on the incremental cost?

  What assumption would need to satisfied for implementations

What assumptions would need to be satisfied for the implementation of Bayes Classifier, Euclidean, Mahalanobis, Parzen windows, Gaussian probability density function, Maximum likelihood parameters estimation of Gaussian pdfs, Naïve Bayes, Guassian..

  Find the voltage reflection coefficient of transmission line

A lossless transmission line, with characteristic impedance of 50Ω and eletrical length of l=0.27λ, is terminated by load impedance 40-j25Ω. Determine voltage reflection coefficient.

  Calculate the field intensity at the center of the loop

A wire is bent in the form of a half loop of radius a=10mm and charged with a line charge density pL=10^-9 C/m. Calculate the field intensity at the center of the loop.

  Calculate the motors starting current

A 1000V, 50 hp compound motor runs at a speed of 750 rpm at full load. The armature, series and shunt field resistances are 0.5 ohm, 1 ohm, and 200 ohm, respectively. The motor efficiency at this condition is 80%. Calculate the motors starting cur..

  Determine how far backed-off must the amplifier operate

If the SNR must be greater than 40 dBm, how far backed-off must the amplifier operate. Assume noise comes from a third-order intermodulation between two interferers with the same power level as the wanted signal.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd