Determine the average shear stress in each pin

Assignment Help Civil Engineering
Reference no: EM13542341

1.The pins on the frame at B and C each have a diameter of 0.25 in. If these pins are subjected to double shear, determine the average shear stress in each pin.

2.A point A on the free surface of a free vortex is at a radius rA = 200 mm and a height zA = 125 mm above datum. If the free surface at a distance from the axis of the vortex, which is sufficient for its effect to be negligible, is 180 mm above datum, what will be the height above datum of a point B on the free surface at a radius of 100 mm?

Reference no: EM13542341

Questions Cloud

Plot a curve showing the relationship of se versus : Plot a curve showing the relationship of Se versus L/r for steel columns. Draw the curve for slenderness ratios that vary from 0 to 200. Assume the proportional limit = 235 MPa
Water is critical to the paper production process : Fresh water enters the process in 3 streams – approx. 0.5 ML/d enters with chemicals at the dry end of the machine, approx. 1 ML/d enters at the wet end of the machine and the boiler consumes approx. 0.2 ML/d.
A conversion of land from tomato farming to cotton is plan : A conversion of land from tomato farming to cotton is planned. Is it true that less water will be used to supplement rainfall based on one growing season ?
Calculate the sequent depth required to form a jump with : Assuming a drag coefficient Cd of 0.6 for the baffle blocks based on the upstream velocity and combined frontal area of the blocks, calculate the sequent depth required to form a jump with the blocks and compare this value to the sequent depth requir..
Determine the average shear stress in each pin : The pins on the frame at B and C each have a diameter of 0.25 in. If these pins are subjected to double shear, determine the average shear stress in each pin.
Should hole a be placed to make the net wind force zero : In strong winds the force can be quite large. Suppose that a hole is introduced in the building’s roof at point A to make pi equal to the surface pressure there. At what angle ? should hole A be placed to make the net wind force zero?
Determine the actual distance below the surface : In the determination of the average velocity of flow in wide rivers, it is common practice to estimate the average velocity in a vertical section by making a single measurement at a distance below
Locate the well screen in the middle of the aquifer : A well installed into a confined aquifer with a porosity of 0.3 and saturated thickness of 80 ft. The gravel pack requires a well screen slot width of 0.025 inches. The hydraulic conductivity of the aquifer is 60 ft/d. The radius of influence is 1200..
Find the conveyance of flow : A flow of 0.1 cum/s flows down in a rectangular channel of width of 0.6m and having and adjustable bottom slope. If chezys constant C is 56, determine the bottom slope necessary for uniform flow with a depth of flow 0.3m. Also find the conveyance of ..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Travel of particle during time period

Determine the acceleration when t = 4 s, the displacement from t = 0 to t = 10 s, and the distance the particle travels during this time period.

  What is the molar flow rate of the feed stream to the column

A mixture containing 45 wt% benzene and 55 wt% toluene is fed to a distillation column. An overhead stream of 95 wt% benzene is produced, and 8.0 % of the benzene fed to the column leaves in the bottom stream.

  What is the critical state angle of friction of the soil

The soil undergoes shear failure and reaches critical state on this plane when the pore-water pressure is increased to 120 kPa while keeping the total normal and shear stresses constant.

  Estimate the hourly production and unit cost of rock

Estimate the hourly production and unit cost of rock excavation by drilling and basting. The rock is limestone having a seismic velocity of 6000 ft/s. Trial blasting indicates that 3" holes drilled in 12 ft.

  Determine the factor of safety against overturning

The factor of safety is defined as the ratio of the stabilizing moment divided by the overturning moment. The densities of concrete and water are = 2.40 and = 1 , respectively. Assume that the dam does not slide.

  What are the reactions-shear forces and bending moments

If you have 10 kips acting downward on a foundation and footing, 4 feet long, with uniformly distributed load acting up ward of 2.5 k/ft (soil) also 4 ft long. what are the reactions, shear forces, and bending moments at the tree critical points

  Compute the amount of chlorine required for disinfection

Compute the amount of chlorine required for disinfection in pounds per day(lb/d). Estimate the annual cost for disinfection using chlorine. Flow Rate= 30 milloin gallons per day.

  The lenght of measurement should be recordesd as how many

A tape that has an extra foot graduated to tenth outside  the zero mark was used to measure a distance less than a tape lenght. when the rear tapeman held the 52-ft graduation at his point, the head tapeman estamted the reading at  as his end of the ..

  Is this level dangerous to the fish population

A lake has a volume of 750,000 m3 (dimensions 15 m deep, 100 m wide, and 500 m long) and behaves as two completly mixed cells. Cell 1 makes up 40% of the lake ( dimensions 15 m deep, 100 m wide, and 200 m long) cell 2 makes up 60% of the lake (dimens..

  What is the maximum cop for this pump if heat is extracted

Consider a house that is heated and maintained at 20oC by a heat pump during the winter. What is the maximum COP for this pump if heat is extracted from the outdoor air at (a) 10oC, (b) -5oC, and (c) -30oC

  A soil sample has the following data

A soil sample has a wet unit weight of 96 lb/ft^3, amoisture content of 17% and a degree of saturation of 60%. Findthe: (A) Void Ratio, (B) Specific gravity, (C) Saturated unitweight.

  Determine the radius of influence of the pumping

A well with a radius of 0.5 m pumps at a constant rate of 1240 m3/day. After the cone of depression has achieved equilibrium, the piezometric heads at two observation wells 40 and 95 m from the pumping well are measured as 78.9 and 83.4 above sea ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd