Determine the average pressure supported by the seal area

Assignment Help Mechanical Engineering
Reference no: EM13933768

When the seawater level inside the hemispherical chamber reaches the 0.6-m level, the plunger is lifted, allowing a surge of sea water to enter the vertical pipe.

For this fluid level (a) determine the average pressure C supported by the seal area of the valve before force is applied to lift the plunger and (b) determine the force P (in addition to the force needed to support its weight) required to lift the plunger. Assume atmospheric pressure in all airspaces and in the seal area when contact ceases under the action of P.

Reference no: EM13933768

Questions Cloud

What is the total dollar return earned : Nancy Cotton bought 400 shares of NeTalk for $15 per share. One year later, Nancy sold the stock for $20 per share, just after she received a $0.50 cash dividend from the company. What is the total dollar return earned by Nancy for the year? What is ..
Explain what are negative externalities : Explain what negative externalities are, and why there may be a case for government intervention to address them. Describe some of the ways to correct the negative externalities and the pros and cons of each method. Provide real life examples.
Critical analysis of a project business case : Word length Assignment 1 should be 2000 words approximately, exclusive of tables, figures, appendices, etc. Software requirement to complete assignment There are no specific software requirements for this assignment, apart from word processing. Yo..
Notoriously conservative in lending to new business firms : In contrast to venture capital, commercial banks are notoriously conservative in lending to new business firms.  What makes venture capitalists more eager to finance risky projects? Suppose you are very favorably considering a venture that has the fo..
Determine the average pressure supported by the seal area : For this fluid level determine the average pressure C supported by the seal area of the valve before force is applied to lift the plunger and (b) determine the force P
What were the results or findings of the research : What were the results or findings of the research? What can be concluded from the research? Are there any future recommendations or limitations that were discussed by the authors?
Financial statement analysis and valuation : Design a spreadsheet and prepare a set of financial statement forecasts for Walmart for Year þ1 to Year þ5 using the assumptions that follow. Project the amounts in the order presented (unless indicated otherwise) beginning with the income statement,..
Measuring growth in sales and selling expenses : Support your answer by measuring growth in sales and selling expenses.
Yorkshire house foods ltd. project orion : A project plan, created using Microsoft Project software, showing a network of tasks, the critical path, human resources required and expected completion times. Use a start date of November 3rd 2014. You must also provide, in text, your appraisa..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calulate the carbon content at 095mm below the surface of

the surface of a steel gear made of 1020 steel 0.20 wt c is to be gas-carburized at 927 deg c. calulate the carbon

  What is the allowable heat dissipation rate if the

electronic components are attached to a 2mm thick 10cm square aluminum plate. the back face of the plate has

  Estimate the temperature of the hottest point in the billet

Estimate the temperature of the hottest point in the billet after five minutes of quenching. Neglect end effects; make the calculation for a cylinder of the given diameter but of infinite length.

  Capacity coefficient of the flow control valve

Determine the required capacity coefficient of the flow control valve

  Survey of industry representatives conducted

A survey of industry representatives conducted by the National Society of Professional Engineers indicated the #1 area in which more coursework was called for was:

  An sae 4140 oqt 1000 sleeve is to be secured to a solid pin

an sae 4140 oqt 1000 sleeve is to be secured to a solid pin of the same material with an actual diametral interference

  The cylinder and hub have a total mass of 30 kg and a

the cylinder and hub have a total mass of 30 kg and a radius of gyration of 0.5 m. assume no slippage. determine the

  Some kg of ari is at an inital pressuuer aand temp of

some kg of ari is at an inital pressuuer aand temp of 1.73mnm2 and 175c it is expanded iso thermal to three volme and

  It has been determined that a point in a load-carrying

it has been determined that a point in a load-carrying member is subjected to the following stress condition sx 400 mpa

  The air passing through the valve has a speed of 300 ms and

a tank of 0.05 m3 volume air at 800 kpa absolute and 15 c. at t0 air begins escaping from the tank through a valve with

  Air standard diesel cycle has a compression ratio

An air standard Diesel cycle has a compression ratio of 15, and the heat transferred to the working fluid per cycle is 800 Btu/lbm. At the beginning of the compression process the pressure is 14.7 lb/in^2 and the temperature is 60 F. Determine the pr..

  The gap between the two plates is h 0005 m the fluid has a

there is flow between two plates as shown in the schematic. the bottom plate is stationary. the top plate is moving at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd