Determine the average normal stress in the links

Assignment Help Civil Engineering
Reference no: EM13551328

As a consultant, you are required to design a swing set of a child whose mass is kg. The diameter of the wire used for constructing the links of the chain is 5 mm. Determine the average normal stress in the links at bottom of the swing, assuming that the inertial forces can be neglected.

Reference no: EM13551328

Questions Cloud

Case of an earthquake the city will lose : What is the probability that in case of an earthquake the city will lose its water supply?
Explain marble is composed of caco3 : Marble is composed of CaCO3. CaCO3 can be made from the reaction of CaO with CO2, How many pounds of CO2 are locked up in 50 Ib of marble
How much force on the input piston is required : A hydraulic jack has an input piston of area 0.050 m^2 and an out put piston of area 0.70m^2. How much force on the input piston is required to a lift a car weighing 1.2 * 10^3 N
Explain the freezing point of a solution that contains : What is the freezing point of a solution that contains 12.0 g of glucose (C6H12O6) in 50.0 g of water (Kf = 1.86°C/m)
Determine the average normal stress in the links : Determine the average normal stress in the links
What is the rotational kinetic energy of smaller cylinder : Two uniform solid cylinders each rotating about its central(longitudinal) axis, have the same mass of 4.92 kg and rotate with the same angular speed of 118rad/s, but they differ in radius
Find the equilibria of the system : Find the equilibria of the system and sketch the direction field for the system - Parameter values obtained from the Beth Israel Deaconess Medical Center.
Delinquency prevention program is being established : A new after-school delinquency prevention program is being established. The Program Director calls you up on the telephone and asks your advice on how to design a good program. What advice can you give her?
Explain what is the change in volume of the balloon : The balloon then rises to an altitude of 6000 ft, when the pressure is 605 torr and the temperature is 15 °C. What is the change in volume of the balloon as it ascends from sea level to 6000 ft

Reviews

Write a Review

Civil Engineering Questions & Answers

  Suggest an alternative engineering design solution that

Stormwater controls are typically designed by civil engineers. Stormwater is collected in pipes below the ground and routed to nearby surface water

  Which measurement contributes to large amount of error

Which measurement contributes to large amount of error? how would you improve on these measurements if you repeated this lab exercise?

  Determine the effluent soluble substrate concentration

Lab studies have shown that the rate constant associated with the process are as follows: k = 0.95 mg COD/mg VSS-day; Y = 0.48 mg VSS/ mg COD, half-saturation K = 85 mg COD/L; ke = 0.07 d-1.

  Compute the maximum acceptable tensile service load

Compute the maximum acceptable tensile service load T that may act on a single angle L6x4x3/4 that is welded along only one leg to a gusset plate; thus, there are no holes. The service load is three times the dead load. Solve for a0 A36 steel.

  General systems theory encourages us to use a holistic

The evaluation of various possible scenarios (either future or past) using simulation models can be tremendously valuable as a tool used in strategic plan development.

  Find the maximum production rate of b in moles per minute

Find the maximum production rate of B in moles per minute and the optimum  for (a) a plug flow reactor (b) a mixed flow reactor Find the production rate of B in moles per minute for (c) a mixed flow reactor with V = 100 m3

  Calculate the mass fractions of the phase present at 700 c

A 50 mg-50 Pb alloy is cooled slowly from 700 C to room temperature, a) Calculate the mass fractions of the phase present at 700 C

  A ferric chloride dosage of 40 mg/l and an equivalent dosage

A ferric chloride dosage of 40 mg/l and an equivalent dosage of lime are used to coagulate a water.

  Determine the basin dimensions if increments are used

A rapid-mixing basin is to be designed for a water coagulation plant, and the design flow for the basin is 4.0 MGD (million gallons per day). The basin is to be square with a depth equal to 1.25 times the width.

  Determine length of roadway that is in full superelevation

Determine the length of roadway that is in full superelevation for a four-lane expressway with a 60 mph design speed. The BC of the curve is at station 15+00 and has a minimum allowable radius. The curve delta is 25 degrees and 30'.

  Determine the incremental rate of return between company

The General Hospital is evaluating new office equipment offered by three companies. The interest rate is 8%. Company A Company B Company C Cost $500 $600 $700 Annual benefit 130 115 100 End of useful life salvage value 0 250 180 Useful life (yrs) 5 5..

  Determine what was the distance between the markers

A 100 ft cut steel tape was used to measure between two property markers. The rear surveyor held 93 ft, while the head surveyor cut .67ft. What was the distance between the markers

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd