Determine the average applied force exerted on to the pile

Assignment Help Mechanical Engineering
Reference no: EM13216511

the hammer of a pile driver of mass 15000kg falls freely through a distance of 2m onto a pile. The impact takes place in 0.02 seconds and the hammer does not rebound. determine the average applied force exerted on to the pile hammer. Note because the force is applied over a short time period it can be considered as an impulse force.

Reference no: EM13216511

Questions Cloud

Discuss what separates sociology from common sense : discuss what separates sociology from common sense? give examples of sociological research might dispel commonly accepted views
What are the angles : solution of oblique-angled triangle all threesides known two side at 7.5 in. and base at .3437 in. what are the angles ?
Determine the power generated by the motor m : Determine the power generated by the motor M at this instant if it operates with an efficiency of epsilon = 0.8.
Describe the kutta condition : Describe the kutta condition.
Determine the average applied force exerted on to the pile : determine the average applied force exerted on to the pile hammer. Note because the force is applied over a short time period it can be considered as an impulse force.
Determine the distance d between the cars : Determine the distance d between the cars at which the driver of car A must apply his brakes to just avoid colliding with carB.
Calcualte the efficiency of centrifugal compressor : I would expect somthing like the requirement to execute the equation, please explain each term in the equation with its engineering units.
What are the uses of wind tunnels including : this is concerned a little more into aerodynamics, what are the uses of wind tunnels including the importance of geometric and dynamic similarity and wind tunnel interference?
Estimate a five-month moving average forecast : The Hartley-Davis motorcycle dealer in the Minneapolis- St. Paul area wants to be able to forecast accurately the demand for the Roadhog Super motorcycle during the next month. From sales records, the dealer has accumulated the data in the followi..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Which of these two processes will produce the largest amount

which of these two processes will produce the largest amount of work? (You must provide a full explanation for your choice).

  Calculate the dimensions of the agitation

For the preliminary design a power of 0.5kW/m^3 volume is to be used. Calculate the dimensions of the agitation system, rpm, and kW power.

  Determine expressions for attractive and repulsive energies

determine the expressions for attractive and repulsive energies, EA and ER as a functions of r where r is in nm and E is in eV.

  What is the change of energy stored in the battery

A 12 Volt battery is charged by supplying 3 Amps over a period of 6 hours. What is the change of energy stored in the battery if the battery loses 400kJ of heat during charging.

  Explain direct stress and strain

Direct Stress and Strain, A steel rod having a cross-sectional area of 0.005m2 and length 3m is attached to supports.

  Evaluate the variation of hoop stresses

Evaluate the variation of hoop stresses across the wall of the compound cylinder.

  Aerodynamics and flight mechanics

Write a short technical report on Frequency Division Multiplexing

  Find the discharge coefficient for flange taps

the reynolds number of a fluid flowing through a 5-cm-diameter, square-edged orifice plate meter within a 15-cm pipe is 250,000. Find the discharge coefficient for flange taps.

  Explain a train accelerates uniformly along a straight track

A train accelerates uniformly along a straight track and passes three trackside markers. The distance between the first two markers is equal to 0.25 km and between the second and third the distance is 0.4km

  Whit is the critical crack length in iron

Whit is the critical crack length in iron according to the Griffith-Orowan equation if surface energy=10^3J/m^2?

  Define- hydraulic mean radius

Define- hydraulic mean radius, hydraulic dept, section factor and most efficient dhannel cross section.

  What speed will the sleeve attain

what speed will the sleeve attain? The temperature oƒ the sleeve remains constant.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd