Determine the asymptotic distribution of the annual maximum

Assignment Help Civil Engineering
Reference no: EM13564938

1.Methane at 10?C and 600 kPa (absolute) is to be transported via pipeline at a flow rate of 0.1 N/s. (a) Calculate the density of carbon dioxide under these conditions and perform an online search to determine the dynamic viscosity of carbon dioxide at the given temperature and pressure. (b) For what range of pipe diameters will the flow be turbulent?

2.Assume that the daily maximum wind speed at a given location follows a Gaussian distribution with a mean speed of 15 mph and a coefficient of variation of 67%. (a) Determine the asymptotic distribution of the annual maximum wind speed for the location, that is, specify the asymptotic type of the distribution and the associated parameters. (b) Using the results of (a), derive the corresponding asymptotic distribution for the 50-year maximum wind speed and estimate its mean value.

Reference no: EM13564938

Questions Cloud

What is the probable total error in the whole distance : A distance is measured through mountainous terrain and found to be 5182.40 ft. If on the average a plumb bob is used every 50 ft with a probable error of ±0.02 ft, what is the probable total error in the whole distance?
Evaluate what is thevalue of the inductance : A 12.0 V battery is connected inseries with a resistor and an inductor. The series circuit has atime constant of 597 µs, and themaximum current is 302 mA. What is thevalue of the inductance
What is thevertical height between the two climbers : A rock climber throws a small first aid kit to another climberwho is higher up the mountain. what is thevertical height between the two climbers
Determine the probability that the weakest pile of this : When standing 10 feet from the base of a building, you measure that the bottom of a large window is at 45 degrees from the horizontal, while the top of the window is at an angle 60 degrees. How tall is the window?
Determine the asymptotic distribution of the annual maximum : Assume that the daily maximum wind speed at a given location follows a Gaussian distribution with a mean speed of 15 mph and a coefficient of variation of 67%. (a) Determine the asymptotic distribution of the annual maximum wind speed for the locatio..
Determine the required air speed in the wind tunnel : A rectangular channel of width b is to carry water at flowrates from 30 ? Q ? 600 cfs. The water depth upstream of the hydraulic jump that occurs (if one does occur) is to remain 1.5 ft for all cases. Plot the power dissipated in the jump as a functi..
Superpave designation and maximum size mixture designations : Assuming you have a roadway with 5 million traffic ESALS, and a Nominal Maximum Aggregate Size of 12.5mm, determine the requirements for:
What would be the semi-annual cash payments that the city : A circular sewer with a 1.5m inside diameter is designed for a flow rate of 15m^3/s when flowing full. Assume that the Manning roughness coefficient and Darcy friction factor are constant with depth of flow. The flow rate when the depth of flow is 0...
Evaluate what is the acceleration of the car : A car is accelerating while its horn is blowing. Just afterthe car passes a stationary person, the person hears a frequency of966.0 Hz. What is the acceleration of the car

Reviews

Write a Review

Civil Engineering Questions & Answers

  Which one of the following would have the greatest impact

A spread footing supported on a sandy soil has been designed to support a certain column load with a factor of safety of 2.5 against bearing capacity failure. However, there is some uncertainty in both: the column load, P, and the friction angle, ?

  Determine what is the gage pressure in chamber a

Two chambers, A and B both have manometers with the same fluid with specific gravity 1.4. When h(sub a) = 6 cm and h(sub b) = 4 cm, what is the gage pressure in chamber A

  When its axis is parallel to the direction of stream flow

A bowling ball is dropped from a boat so that it strikes the surface of a lake with a speed of 25 ft/s. Assuming the ball experiences a downward acceleration of a = 10-9v2 when in the water, determine the velocity of the ball when it strikes the bott..

  Determine the perpendicular distance from o to cable bd

A precast concrete wall section is temporarily held by two cables as shown. Knowing the tension in cable BD is 900 N, determine the moment about point O of the force dxerted by the cable at B. Next determine the perpendicular distance from O to cable..

  Calculate the area of a piece of property bounded

Calculate the area of a piece of property bounded by a traverse and circular arc with the following coordinates at angle points: A (1275.11, 1356.11), B (1000.27,1365.70),C

  Determine the tangential component of the acceleration

determine the tangential component of the acceleration of the sled a) just before it reaches B, b) just after it passes C.

  Determine the value for cohesion intercept c

Separate triaxial compression tests are performed on identical soil samples. The soil is a saturated mixed soil. Both tests follow the procedure for consolidated-undrained conditions.

  At what angle did the player have to shoot the cue ball

(a) At what angle did the player have to shoot the cue ball so that the eight ball entered the pocket at C? (b) In what direction did the cue ball move after the collision? (c) What percentage of its kinetic energy did the cue ball impart to the e..

  Advantages and disadvantages of various training strategies

Depending on the needs and understanding the applications, technology, and operations of your organization will help in making the right decisions when acquiring an EHR system

  Determine the increase in vertical stress at 2m below ground

Three parallel line loads of 500kN/m are applied at ground level in a straight line 4.0m apart. Determine the increase in vertical stress at 2.0m below ground level beneath the middle load.

  Determine the modulus of elasticity and proportional limit

A tension specimen has a gauge length of 8 inches and a diameter of .505 inches. A load of 9580 pounds was found to develope a stress in the specimen equal to the proportional limit of materials. ( assume that the proportional limit and the yield ..

  What are values of yield stress fy ultimate tensile stees

a w24x192 of a242 steel is to be used as a beam. what are the values of yield stress Fy ultimate tensile stees Fu and modulus of elasticity E for this beam

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd