Determine the astm grain size number if 25 grains per

Assignment Help Mechanical Engineering
Reference no: EM13630274

1): For an ASTM grain size of 8 , approximately how many grains would there be per square centimeter :

(A) at a magnification of 100x , and (b) without any magnification?

2): determine the ASTM grain size number if 25 grains per square centimeter are measured at a magnification of 600x?

3): determine the ASTM grain size number if 20 grains per square centimeter are measured at a magnification of 50x?

Reference no: EM13630274

Questions Cloud

A cylinder conductor with radius 2r and length l carries a : a cylinder conductor with radius 2r and length l carries a uniformly distributed net charge q. this conductor is
At steady state a refrigeration cycle removes 18000 kjhr of : at steady state a refrigeration cycle removes 18000 kjhr of energy by heat transfer from a space maintained at -40oc
Determine the time rate of change of temperature of a fluid : the temperature distribution in a fluid is given by t 10x 5y where x and y are the horizontal and vertical coordinates
A power cycle operates between a reservoir at temperature t : a power cycle operates between a reservoir at temperature t and a lower temperature reservoir at 280ok. at steady state
Determine the astm grain size number if 25 grains per : 1 for an astm grain size of 8 approximately how many grains would there be per square centimeter a at a magnification
Find an expression for the classical turning points of a : a find an expression for the classical turning points of a quantum harmonic oscillator.b calculate the probability for
The city of houston has a water filtration system that : the city of houston has a water filtration system that consists of a large rigid tank with a single 1.5m diameter inlet
Consider a simple brayton cycle using air as the working : consider a simple brayton cycle using air as the working fluid has a pressure ratio of 12 has a maximum cycle temp of
The city of houston has a water filtration system that : the city of houston has a water filtration system that consists of a large rigid tank with a single 1.5m diameter inlet

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compare the thermal efficiency of a two-stage gas turbine

compare the thermal efficiency of a two-stage gas turbine with regeneration reheating and intercooling to that of a

  The discharge temperature is 400 c a heat loss of 10 kw is

a steam compressor is used to increase the pressure of saturated water vapor at 1000 kpa to 1500 kpa. the flow rate is

  The wet feed material to a continuous dryer contains 50 wt

the wet feed material to a continuous dryer contains 50 wt water on a wet basis and is dried to 27 wt by countercurrent

  A part subjected to a stress of 50 ksi may experience a

a part subjected to a stress of 50 ksi may experience a single edge surface crack no longer than 0.015 in. which if

  A two ton 4000 ibf weight is suspended on a 30 foot long

a two ton 4000 ibf weight is suspended on a 30 foot long half inch diameter steel cable. what was the original length

  Piece of steel will be placed in a carbon-rich atmosphere

Subject a piece of steel to a case hardening process in which carbon is forced by diffusion through a layer on the surface of the piece. For this purpose, the piece of steel will be placed in a carbon-rich atmosphere in a special furnace.

  For the ideal air standard diesel cycle with a volumetric

for the ideal air standard diesel cycle with a volumetric compression ratio of 17 1 calculate the efficiencies for

  At the position of the negative charge what is the

three equal charges of magnitude q6.00 uc are located at three corners of a square edge length d2.9 cm. a negative

  What is the effect of immersion depth

What is the effect of immersion depth on a glass electrode and what aspects of the design of a pH electrode installation would lead to reduced manual maintenance and improved reliability

  A rigid container is filled with 1 kg of waterthe volume

a rigid container is filled with 1 kg of water.the volume of the container is 125-l.the initial pressure of the

  After drawing a neat and clear schematic of the geometry

a 5 ft3 tank containing steam at 14.7 psia 1 quality is fitted with a relief valve. heat is transferred to the tank

  If the low temperature reservoir is held fixed at 300 k

joe smith claims to have designed a power cycle that can achieve a net power output of 400 mw given a heat input of 500

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd