Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Problem:Determine the ASD reference and adjusted design values for the following members and loading conditions. All members are Select Structural Southern Pine and are fully braced to prevent lateral torsional buckling. Bending Occurs about the strong axis.
Given:1. Roof joists are 2x6 at 24 inches on center which directly supports the roof sheathing. Loads are D+S2. A 4x12 that supports D+L+Lr3. Purlins in a roof are 2x10 inches at 4ft on center. Loads are D+Lr4. Floor beams are 4x10 at 4ft on center. Loads are D+W+L
differential leveling between benchmarks A,B,C,D, and A gives elevation differences(m) of -15.632, 32.458, 38.214, and -55.025, and distances(km) of 4,6,5, and 3 respectively.
Saturated liquid water at 1.0 MPa is throttled adiabatically to a pressure of 0.4 MPa. If the change is kinetic energy is negligible, what percentage of the water evaporates during this throttling process
In the field, if the relative compaction is 90%, determine the hydraulic conductivity of the sand in the field compaction condition (given that k for the sand at the maximum dry density condition is .040 cm/sec and Gs = 2.65).
The company can either buy a single 200m^3 ideal plug flow tank, or three 80m^3 completely mixed tanks that operate in series. the cost is essentially the same. The pollutant is removed as a part of a first order reaction with a rate constant value..
the block is fitted between the fixed supports. if the glued joint can resist a maximum shear stress of T(allow)=2ksi, determine the temperature rise that will cause the joint to fail. Take E= 10(10^3)ksi, v=0.2
The allowable shearing stress is 15 ksi in the steel rod AB and 8 ksi in the brass rod BC. Knowing that the torque of magnitude T=10 kip * in. is applied at A, determine the required diameter of a) rod AB, b) rod BC.
By assuming a linear speed-density relationship, the mean free flow speed on a highway facility lane equals 65 mph. The jam density is observed to be about 170 vpm. 1. Plot the q-k-u curves
Assume the microorganisms are 55 percent efficient at converting food to biomass, the organisms have a first-order death rate constant of 0.05/day, and the microbes reach half of their maximum growth rate when the BOD5 concentration is 10 mg/L
A steel I beam is supported by a pin at point A and a rocker at B, and a cable applies a 2000lb force. The beam is uniform and weighs 26 lb/ft. Determine the support reactions.
A piston-cylinder device contains 2 kg saturated water vapor at 600 kPa. The water expands adiabatically until the final pressure is 100kPa. And 1,465 kJ work is produced.
How do the concepts of green design, industrial ecology, and sustainable developement differ from past approaches to engineering design Prepare a brief report on this topic using some specific examples for illustration.
The motion of the 2.5-kg rod AB is guided by two small wheels which roll freely in horizontal slots. If a force P of magnitude 8 N is applied at B, determine (a) the acceleration of the rod, (b) the reaction at A and B.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd