Determine the amount of heat that must be removed

Assignment Help Mechanical Engineering
Reference no: EM13216837

A vessel with a volume of 0.0011 m3 is filled with dry saturated steam at a pressure of 95 kPa. It is then sealed and cooled to 250C. Determine the amount of heat that must be removed.

Reference no: EM13216837

Questions Cloud

What is the concentration of fecl3 in a solution : What is the concentration of FeCl3 in a solution prepared by dissolving 20.0 g of FeCl3 in enough water to make 275 mL of solution?
Uniform crime report and self-report data : Complete the matrix below. To complete this matrix, list two pros and two cons of Uniform Crime Report (UCR) data and two pros and two cons of self-report data.
What is the proeutectoid phase : Consider 6.0 kg of austenite containing 0.45 wt% C, cooled to below 727 degrees Celcius (1341 degrees Farenheit).
How increasing the attractiveness of the debt securities : Both convertibility and warrants attached to debt aim at increasing the attractiveness of the debt securities and lowering the interest cost.
Determine the amount of heat that must be removed : A vessel with a volume of 0.0011 m3 is filled with dry saturated steam at a pressure of 95 kPa. It is then sealed and cooled to 250C. Determine the amount of heat that must be removed.
Calculate the adiabatic flame temperature : Calculate the adiabatic flame temperature (at constant pressure) for ethane C2H6 in air
State political practices-impact human resource management : When businesses operate across countries, how does diversity-in cultures, socioeconomic factors, or political practices-impact human resource management?
How many engagement points on the flywheel : How many engagement points on the flywheel would be necessary to make this machine safe?
Different marginalized populations : What would you say is the overall lesson from the simulation activity? How do you improve communication between caregivers and patients with low health literacy? Patients with disabilities? Children?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the rotating speed of the disk in rpm

A slotted disk and opto-interrupter outputs pulses at 62 HZ. The disk has only one slot cut in it. what is the rotating speed of the disk in rpm?

  Determine the velocity va

The catapult is used to launch a ball such that it strikes the wall of the building at the maximum height of its trajectory. If it takes 1.5 s to travel from A to B, determine the velocity vA at which it was launched, the angle of release q, and t..

  What is the actual strain

You have a 120 Ω quarter bridge 2 wire set up with Sg=2.10 and an unknown lead wire resistance. A 59880Ω calibration resistor is switched in parallel to the gage only and a recording instrument is set to give a -100 mm deflection for this calibrat..

  Explain working with boiler suspension bolts

Working with boiler suspension bolts. An HRT boiler is 4766mm long and 3533mm in diameter. It has 66 steel tubes with a diameter of 9mm. The total dry weight of the boiler is 2.565 tonnes

  How did you do the maintenance during your workshop

Show how did you do the maintenance during your workshop

  What is the specific volume

what is the specific volume, internal energy (kj/kg) and enthalpy (kj/kg) for water at 1.8 mpa and 120 Degrees C? Locate the state on p-v diagram and document assumptions.

  Find the natural frequency

Three springs anda mass are attached to a rigid, weightless bar PQ hinged at one end. How do I find the natural frequency?

  What tightening torque should be used

What tightening torque should be used if the connection is permanent and the fasteners are lubricated? What portion of the external load is taken by the bolts? By the members?

  Calculate the adiabatic flame temperature

Calculate the adiabatic flame temperature (at constant pressure) for ethane C2H6 in air

  Evaluate the maximum theoretical power

Evaluate the maximum theoretical power that can be developed by the turbine, in kW, and the corresponding exit temperature.

  Calculate shaking force and shaking torque

find Torque at O2, and forces at O2, A and B, also calculate shaking force and shaking torque. MEE40003- Machine Dynamics

  Heat is transferred to the steam until the temperature

A piston-cylinder device has a volume of 0.1 cubic meters and contains 0.5kg of steam at 0.4 MPa. Heat is transferred to the steam until the temperature is 300 degrees Celsius

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd