Determine the amount of 100 psi saturated steam

Assignment Help Chemical Engineering
Reference no: EM131312458

100 moles of a fuel containing methane and butane is burned with 25% excess air in a furnace producing stack gas at 300 degrees C and 105 kPa. Determine the amount of 100 psi saturated steam that can be produced from water fed in at 10 degrees C, if

a) The stack gas does not contain methane, butane or CO,

b) The dew point of the stack gas is 58 degrees C, and

c) The air enters at 20 degrees C as dry air.

Reference no: EM131312458

Questions Cloud

How can dfa be considered an active and passive investor : Write a composed essay (1 page max) addressing the following questions: (1) How can DFA be considered an active and passive investor at the same time?
What will be the change in the value of your firm : Your factory has been offered a contract to produce a part for a new printer. The contract would last for five years and your cash flows from the contract would be $3 million per year. Your upfront setup costs to be ready to produce the part would be..
Appreciative inquiry interview questions : Suppose your supervisor has asked you to lead an Appreciative Inquiry process and as a first step you need to conduct some interviews with your coworkers. Do a search on "Appreciative Inquiry Questions" or "Appreciative Inquiry Interview Questions..
Apply the content from the articles to social networking : Primary sources such as government websites (United States Department of Labor - Bureau of Labor Statistics, United States Census Bureau, The World Bank), peer reviewed and scholarly journals in EBSCOhost (Grantham University Online Library) and G..
Determine the amount of 100 psi saturated steam : 100 moles of a fuel containing methane and butane is burned with 25% excess air in a furnace producing stack gas at 300 degrees C and 105 kPa.
Questions concenring videos on future search-open space : Harrison Owen is the developer of Open Space Technology. He also has a few videos up on YouTube as well. Take a look at some of his videos and share the link to one that you found to be the most useful. Answer the following questions concenring th..
Create a job description for a retail sales associate : Create a job description for a retail sales associate, which includes the most significant components necessary to describe the job both internally and externally.Create an organizational behavior modification (OBM) plan to define four (4) key be..
Find the amount of lime & soda req. to soften the water : amounts of hardness (in mg per l) are asmgso4=120 ca(no3)2=164 cacl2=222 mg(hso4)2=73 lime and soda are of 74% and 73% purity respectively.
Reliant on hard data and results from adaptation : What type of strategy is not exclusively reliant on hard data and results from adaptation, experience, and the forces that impinge upon the organization?

Reviews

Write a Review

Chemical Engineering Questions & Answers

  Dehydrogenated to ethylene

Ethane (C2H6) can be dehydrogenated to ethylene (C2H4), which can be dehydrogenated further to acetylene (C2H2). A reactor is fed with ethane and steam at a 1:1 mole ratio (The steam simply acts as a diluent). If the reactor runs at 1 atm and the rea..

  Evaluate the frequency for each of the waveforms

Three waveforms seen on an oscilloscope are shown in Figure P1.4.7. If the horizontal scale is set to 50 ms per division (500 ms for the entire screen width), and the vertical scale is set to 5 mV per division (±25 mV for the entire screen height ..

  Is such a control scheme feasible

Is such a control scheme feasible? What would the designers need to do to eliminate potential problems?

  Calculate the molar flow rate (mol/h) of the feed gas

Following 5.0 hours of operation, the pellets are reweighed and found to have a mass of 3.52 kg. Calculate the molar flow rate (mol/h) of the feed gas and the mole fraction of water vapor in the product gas.

  Estimate the heat loss from a facing side of an oven

Explore the effect of the spacing on the heat loss. At what spacing is the heat loss a maximum? Describe the boundary layer behavior for this condition. Can this condition be analyzed by treating the side of an oven as an isolated vertical plate?

  How long does she have to do the experiment

She then determines that to do an experiment, the radioactivity cannot fall below 25% of the initial measured value. How long does she have to do the experiment?

  Draw a block diagram for the controlsystem

Draw a block diagram for the controlsystem.

  Calculate the required rate of heat transfer

The heat of formation of (NH4)2SO3 (aq) at 25°C is -890.0kJ/mol, and that of NH4HSO3 (aq) is -760 kJ/mol. The heat capacities of all liquid solutions may be taken to be 4.0 J/(g*°C) and that of the flue gas may be that of nitrogen. Evaporation of ..

  Calculate the induced voltage

A four-pole, lap-wound armature has 144 slots with two coil sides per slot, each coil having two turns. If the flux per pole is 20 mWb and the armature rotates at 720 r/min, calculate the induced voltage, given that the number of parallel paths is..

  Design a reactor to remove 1% acetylene from ethylene

Design a reactor to remove 1% acetylene from ethylene in a plant that produces 1.5 million metric tons per year of ethylene using this catalyst.

  Satisfactory quality the ratio

We have a mixture consistingof 90 mole% 'A' (45 mol/lit) and 10 mole%impurity 'B'(5 mol/lit). To be satisfactory quality the ratio of 'A' to 'B' in the mixture must be 100 to 1or higher.

  Catalytic or thermal cracking process

When heavy oils are cracked in a catalytic or thermal cracking process, lighter hydrocarbon compounds are formed. Most cracking processes on heavy oil feeds form products with carbon numbers ranging from two to greater than twenty.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd