Determine the a temperature of air before it enters the

Assignment Help Mechanical Engineering
Reference no: EM13633696

Consider an air conditioning system where warm, humid air flows first over cooling coils, where it is cooled and dehumidified, and then over an electrical heater where it is reheated to the desired end temperature. In one application air at 1 atm, 34°C, 70% relative humidity flows through a system of this type, where it exits at 22°C, 50% relative humidity. Assume that any condensate is removed at 10°C. Determine the (a) temperature of air before it enters the heating section, (b) the amount of heat removed in the heating section (kJ/kg dry air), and (c) the amount of heat transferred in the heating section (kJ/kg dry air). Use the psychrometric chart for this solution.

Reference no: EM13633696

Questions Cloud

In an effort to improve the vocabulary of 10 students a : in an effort to improve the vocabulary of 10 students a teacher provides a weekly 1 hour tutoring session for them. a
The air outside the balloon has a temperature of 200degc : a hot-air balloon is open at the bottom. the balloon which has a volume of 214 m3 is filled with air that has an
Also if plastic rod is rubbed with fur and acquires a : a glass rod is rubbed with silk and acquires a charge of magnitude 7.50 nc. what is the change in mass of rod?also if
1081 1076 1051 1048 1034 1032 103 1028 1028 1026 determine : the fastest pitch ever thrown by a major league baseball pitcher was thrown by nolan ryan in 1974 and registered
Determine the a temperature of air before it enters the : consider an air conditioning system where warm humid air flows first over cooling coils where it is cooled and
A double-convex lens is to be made of glass with an index : a double-convex lens is to be made of glass with an index of refraction of 1.5. one surface is to have twice the radius
The automobile then undergoes a uniform acceleration of -4 : an automobile and train move together along parallel paths at 20.7 ms.the automobile then undergoes a uniform
Determine the force between the jaws of the clamp in terms : determine the force between the jaws of the clamp in terms of a torque exerted on the handle of the adjusting screw.
A a tennis ball is dropped from 151 m above the ground it : a a tennis ball is dropped from 1.51 m above the ground. it rebounds to a height of 0.822 m.with what velocity does it

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A natural gas-fired boiler in a textile plant in sharjah is

a natural gas-fired boiler in a textile plant in sharjah is used to provide steam at 130oc. at times of high demand the

  How many raindrops are in each cubic yard of air

if it is raining steadily at a rate of one inch per hour a container with perpendicular sides and a flat bottom would

  Assume frictionless flow through all piping and heat

a walk-in cooler using a vapor compression refrigeration cycle is configured as shown below. the cycle uses cfc22 or

  Saturated water vapor at 350c is heated at a constant

saturated water vapor at 350c is heated at a constant pressure until its volume has doubled. determine the final

  Based of thermodynamic considerations does this system work

one of your classmates claims to have invented a flow device to increase the superheat of steam. his claim is that he

  Steam at 200 c and 7 bars enters a mixing tank at a rate of

steam at 200 c and 7 bars enters a mixing tank at a rate of 3 kgmin through a pipe with a cross-section of 1.20 cm2.

  It is heated as it passes through the tube so that it

water enters one end of a long coiled tube at 5000 kpa 220c at a steady rate of 2.20kgs. it is heated as it passes

  Determine the maximum weight of block c if block b is not

a 10-lb block b rests as shown on a 20-lb bracket a. the coefficients of friction are us0.3 and uk0.25 between block b

  A new prototype proven to perform with an isp of 1000s but

when deciding what propulsion system is most appropriate for a mission thrust and isp are not the only parameters that

  For a product at an aql of 25 and lot size of 5000 using

for a product at an aql of 2.5 and lot size of 5000 using mil standard 105e what is the probability of going to

  Explain discharges to a nozzle for additional thrust

In the an ideal turbo jet, the engine is designed such that the turbine work is divided equally between the compressor and the propeller. The gas from the turbine discharges to a nozzle for additional thrust.

  More air is added until the pressure and temperature rise

a rigid tank contains 20 lbm of air at 20 psia and 70degf. more air is added until the pressure and temperature rise to

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd