Determine shunt resistance needed to convert ammeter

Assignment Help Electrical Engineering
Reference no: EM13293678

Determine the shunt resistance needed to convert a galvanometer to an ammeter with a full scale reading of 10A if the scale requires 2.5mAto cause full deflection with a coil resistance of 10Ω.

Reference no: EM13293678

Questions Cloud

How much total interest is paid over the life of the loan : Prepare an amortization schedule for a five-year loan of $50,000. The interest rate is 8 percent per year, and the loan calls for equal annual payments. How much interest is paid in the third year? How much total interest is paid over the life of ..
Create a mask set and process flow that will produce a wheel : Using combination of deposited oxide and polysilicon films, create a mask set and process flow that will produce a wheel that can rotate freely about a hub that extends over the top of the wheel.
How much will the company earnings per share be diluted : Based on that information, what long-run growth rate can the firm be expected to maintain? (Hint: g = Retention rate x ROE.)
Determine the pendulums length : A pendulum makes 24 oscillations in 39s. The period is 1.6 s 1. Find the pendulum's length
Determine shunt resistance needed to convert ammeter : Determine the shunt resistance needed to convert a galvanometer to an ammeter with a full scale reading of 10A if the scale requires 2.5mAto cause full deflection with a coil resistance of 10Ω.
Determine the maximum inductance of the tank circuit : A tank circuit in a radio transmitter is a series RCL circuit connected to an antenna. determine the maximum inductance of the tank circuit
What is the cash flow from assets for 2011 : What is the cash flow from assets for 2011? (Negative amount should be indicated by a minus sign.)
Hoe to produce a logic diagram for the design : A circuit is needed to divide a 10 Hz signal down to 1 Hz using only a 7493 4-bit counter. Produce a logic diagram for the design.
Determine the bodys capacitive reactance : In one measurement of the body's bioelectric impedance, values of Z = 5.62 x 102 and = -9.14° are obtained for the total impedance, Determine the bodys capacitive reactance

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What value of resistance should the voltage divider have

A voltage divider can provide a voltage at its output, but it cannot provide current. If a device is connected to the output of a voltage divider, what value of resistance should it have

  Determine minimum sampling rate that can be used to sample x

a) Draw a sketch of the spectrum of x(t) = sin3(400πt) Label the frequencies and complex amplitudes of each component. Determine the minimum sampling rate that can be used to sample x(t) without aliasing for any its components.

  What is the impulse response for the system

Consider the following differential equation, where x(t) is the input and y(t) is the output: d/dt y(t)+5y(t)=2x(t) Suppose the input is x(t) = 4u(t) and the initial condition is y(0-) = 6 1. What is the impulse response for the system

  Determine what is the corner frequency of amplifier

An Amplifier hasa low pass STC frequency response. the magnitude of the gain is 20dB at dc and 0dB at 100KHz. What is the Corner frequency At what frequency is the gain 19dB At what frequency is the phase -6degrees

  Determine the s-n improvement due to the pre-emphasis

An FM receiver is modulated with a signal having a baseband bandwidth of 15 kHz and the maximum frequency deviation is 45 kHz. Assume that preemphasis is added with a 3-dB boost frequency of 5 kHz.

  Find real-reactive and apparent power for each phase

A residential four-wire system supplies power at 220V rms to the following single-phase appliances: On the first phase, there are ten 75-W bulbs. On the second phase, there is a 750-W vacuum cleaner with a power factor of 0.87.

  Calculate the magnitude of the line voltage at the terminals

when the load is removed from the generatorthe magnitude of the terminal voltage is 34500V. the generator feeds a delta-connected load through a transmission line with an impedence of 0.8+j6.4. the per-phase impedence of the load is2877-j864.

  Discuss why a project plan is not a microsoft project file

what is meant by "proactive" project management. Discuss ways in which to ensure that projects are being managed proactively. Investigate on the internet the features of Microsoft Project. Discuss why a project plan is not a Microsoft Project file.

  Explain what is the chemical shift difference

From the 1H NMR perspective, the human body is composed primarily of fat hydrogens and water hydrogens (H2O). The resonance frequency difference between the NMR signal from these two types of hydrogens is approximately 220 Hz on a 1.5 Tesla imager..

  Determine what will be the value of the four outputs

Provide an output V to indicate that at least one of theinputs is present. The input with the highest subscript number has the highest priority. What will be the value of the four outputs if inputs D2 and D6 are 1 at the same time

  How fast have an angular momentum spin

How fast, in rpm, would a 100 g, 50-cm diameter beach ball have to spin to have an angular momentum of 0.10 kg m^2/s

  What is the maximun temperature that the device may operate

A GaAs device is dopeed with a donor concentration of 3*10^15 cm^-3, For the device to operate properly, the intrinsic carrier cconcentration must remain less than 5 percent of the total electron concentration.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd