Determine required diameter of each reinforcing steel bar

Assignment Help Civil Engineering
Reference no: EM13297048

A circular concrete column of 300 mm diameter, is reinforced with six identical steel bars. If the column is subjected to an axial compressive force of 800 kN, determine the required diameter of each reinforcing steel bar so that one-third of the load is carried by the steel and two-thirds by the concrete. Assume Esteel= 200 GPa and Econcrete= 25 GPa.

Reference no: EM13297048

Questions Cloud

Determine what is the balance delay for the solution : A proposal has been submitted to replace a group of assembly workers, each working individually, with an assembly line. The following table gives the individual work elements. The demand rate for this job is 1600 units/week (assume 40h/week)
Estimate for p is the proportion : The method of maximum likelihood for estimating p states that we should choose the value for p that gives the highest probability of getting what we got on the experiment.
Explain the standard enthalpies of formation : A scientist measures the standard enthalpy change for the following reaction to be -1053.4 kJ : 2H2S(g) + 3 O2(g) 2H2O(g) + 2 SO2(g) Based on this value and the standard enthalpies of formation for the other substances, the standard enthalpy of fo..
Determine what is the maximum daily mass of chloride : The pipe has a flow of 5 m3/s. The stream's chloride concentration just upstream of the pipe's dischage is 12 mg/L, and the runoff pipe's discharge has a chloride concentration of 40 mg/L. Chloride is a conservative substance.
Determine required diameter of each reinforcing steel bar : If the column is subjected to an axial compressive force of 800 kN, determine the required diameter of each reinforcing steel bar so that one-third of the load is carried by the steel and two-thirds by the concrete. Assume Esteel= 200 GPa and Econ..
Determine the speed of the players break shots : Pool players often pride themselves on their ability to impart a large speed on a pool ball. they have placed you in charge of determining the speed of the players\' break shots
Explain often produced by reaction of zinc with hcl : Small amounts of hydrogen gas are often produced by reaction of zinc with HCl; Zn(s) + 2 HCl(aq) ® H2(g) + ZnCl2(aq) How many liters of H2 gas, collected over water at a pressure of 176.6 mm Hg and temperature of 22.00 °C
Show the whole analysis : Their net income is taxed at a 31% rate. Do a cash flow analysis, show the whole analysis, and recommend whether the new machine should be bought now or in 3 years when the old press must be replaced. Project WACC is 9.5%. Provide NPV, IRR, MIRR &..
Determine what is the order and class of the leveling : Differntial Leveling between BM's A,B,C,D, and A gives elevation differences (in meters) of -15.632, 32.458, 38.214, and -55.025, and distances in km of 4.0, 6.0, 5.0, and 3.0 respectively.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the density of air and weight of the air in the tank

An empty air tank has a volume of 0.024 m3. The compressor on the tank is run until the pressure gauge reads about 65 psi (or 22,500 Pa). Assuming the temperature of the tank is 25 C, find the density of the air and the weight of the air in the ta..

  Determine what is the total elongation of the pipe

a prismatic bar AB of length L, cross section A, modulus of elasticity E, and weight W hangs vertical under its own weight. if the bar is a riser pipe hanging from a drill rig at sea, what is the total elongation of the pipe

  Estimating annual erosion

Using the USLE, estimate the annual erosion from a 100 ha. forested watershed assuming the following: R =112 tonnes/ha/year. The forest is in fair condition with 40% cover; Average slope is 3%; The soils are clay loam in hydrologic group C.

  Evaluate the acceleration along and normal to the path

The velocity along a pathline is given by V (m/s) = s^2 x t^(1/2) where s is in meters and t is in seconds. The radius of curvature is 0.5 m. Evaluate the acceleration along and normal to the path at s = 2m and t = 0.5 seconds.

  What is the maximum height

The height (in meters) of a projectile shot vertically upward from a point 2 m above ground level with an initial velocity of 24.5 m/s is h2+24.5t-4.9t^2 after t seconds. a) When does the projectile reach its maximum height? b) What is the maximum..

  Pulling automobile by means of two ropes

A disabled automobile is pulled by means of two ropes as shown. The tension in AB is 400 lb and the angle is 20. knowing that the resultant of the resultant of the two forces applied at A is directed along the axis of the automobile, determine by ..

  Determine the value of gravity in units of meters

if a ball is dropped from a height of 800 cemtimeters, and the impact velocity is 41 feet per second, determine the value of gravity in units of meters per second.

  Determine was the pavement wet or dry

The driver of a car traveling up a 2% grade at an initial speed Vo applied the brakes abruptly and the vehicles slid to a complete stop at an average deceleration of 8 ft/s^2. Was the pavement wet or dry

  Calculating largest tolerable internal crack length

Calculate the largest tolerable internal crack length for a 7075-T651 aluminum alloy component that is loaded to a stress one-half of its yield strength without catastrophic fracture.

  Magnitudes of fac and fad

The 70 m tall tower is supported by three cables that exert forces FAB, FAC, and FAD on it. The magnitude of the force FAB is 2 kN. The x and z components of the vector sum of the forces exerted on the tower by the three cables are zero. What are ..

  Explain why not use rubber to seal wine bottles

Cork is used for sealing sparkling wine bottles. Aside from friction, why not use rubberbto seal wine bottles. (Hint: think about the force exerted by the pressure inside and how does that deform each material) Be sure to use poissons ratio in the..

  Existing equal tangent sag curve

An overpass is being built over the PVI of an existing equal tangent sag curve. The sag curve has a 70 mi/h design speed, and G1 = -6%, G2 = +3%.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd