User Account

All Pages

Determine rate of heat transfer from the wire and if air

Assignment Help Mechanical Engineering
Reference no: EM13638831

A 2-cm long section of a 3-mm in diameter wire is maintained at a constant surface temperature of 370C. The wire is subject to a cross-flow of air at 30C at 6m/s.

Determine rate of heat transfer from the wire and if air mass flow rate over wire is 0.15 kg/s, determine air temperature gain from the heat exchange process.

Reference no: EM13638831

Questions Cloud

Compute the shaft-power output and isentropic efficiency : steam flows through a small steam turbine at the rate of 10000 kgh entering at 600oc and 2.0 mpa and emerging at 0.01
An adiabatic piston-cylinder system contains a 1000-w : an adiabatic piston-cylinder system contains a 1000-w immersion heater and 4kg of h2o initially at 1 atm and 96 percent
If a balloon is filled with helium until the diameter is : a tank with volume 0.100m3 is filled with helium gas. if a balloon is filled with helium until the diameter is 30.0cm
The percent of observations from the n210 52 distribution : scores on the act test for the 2010 high school graduating class had mean 21.0 and standard deviation 5.2. in all
Determine rate of heat transfer from the wire and if air : a 2-cm long section of a 3-mm in diameter wire is maintained at a constant surface temperature of 370c. the wire is
The reaction n2g 3h2g lt--gt2nh3g is at equilibrium in : the reaction n2g 3h2g lt--gt2nh3g is at equilibrium in areaction chamber. if an experimenter injects a small amount of
Find a draw a schematic of the power cycle b determine the : ocean temperature energy conversion otec power plants generate power by utilizing the naturally occurring decrease with
Explain what happens to pressure on the molecular level : 1. explain what happens to pressure on the molecular level when the number of moles of gas is increased at constant
How much ice in grams would have to melt to lower the : how much ice in grams would have to melt to lower the temperature of 353 ml of water from 26 degrees c to 6 degrees c?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the force in member bc

Determine the force in member BC. After the truss is sectioned use a single equation of equilibrium for the calculation of each force. State if these member is in tension or compression. Take F1 = 2 kN , F2 = F3 = 3.8kN , F4 = 5 kN, F5 = 3 kN.

  The turbine and pump have isentropic efficiencies of 88 for

water is the working fluid in a vapor power cycle. the pressure and temperature at the turbine inlet are 1600 psia and

  Two points b and c lie on radial line of a rotating disk

two points b and c lie on radial line of a rotating disk. the points are 2 inches apart. vb700 ftmin and vc880ftmin.

  A computer cpu chip operates at steady state with d-c

a computer cpu chip operates at steady state with d-c electrical input of 4.5 amps at 9 volts. to prevent the chip from

  Find the relationship between the axial stress sigma shear

a thin wall tube is subjected to combined tensile and torsional loading. find the relationship between the axial stress

  Determine the pressure inside the cylinder

the piston has a mass of 4kg and cross-sectional area of 35cm^2. A compressed spring above the piston exerts a force of 60N on the piston. if the atmospheric pressure is 95kPa, determine the pressure inside the cylinder.

  Consider a steam power plant that operates on a

consider a steam power plant that operates on a regenerative ranking cycle and has a net power output of 150mw .steam

  A differential thermocouple with sensors at the inlet and

a differential thermocouple with sensors at the inlet and exit of a pump indicates that the temperature of water rises

  Determine the points on the tire that have a maximum and

if the tires do not slip on the pavement determine the points on the tire that have a maximum and minimum speed and the

  If this air conditioning system draws 5 kw of power when

an air conditioning system is used to maintain a house at 20 degrees celcius when the outside temperature is 35 degrees

  The two sides of a v-shaped water trough are hinged to each

the two sides of a v-shaped water trough are hinged to each other at the bottom where they meet as shown in figure q1

  At the beginning of compression p1 85 kpa and t1 305 k

an air-standard otto cycle has a compression ratio of 7.5. at the beginning of compression p1 85 kpa and t1 305 k.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd