Determine net rate of heat transfer for ambient reservoir

Assignment Help Mechanical Engineering
Reference no: EM13711552

A heat pump supplies 40 kW of heat to maintain the inside of a house at 25 degree C in cold winter months when the ambient temperature is 00C. Power required to operate the heat pump cycle is provided by a heat engine cycle which receives 10 kW of heat from a reservoir at 500 degree C. The heat engine has thermal efficiency of 50%. The heat engine rejects heat to the ambient reservoir at 00C.

a) Calculate the coefficient of performance of the heat pump.

b) Determine the net rate of heat transfer (kW) for the ambient reservoir.

Reference no: EM13711552

Questions Cloud

Determine the specific internal energy at the final state : A vertical piston/cylinder device contains 0.01 lbm of gas. The initial gas volume is 0.18 ft3 and the initial specific internal energy is 282 Btu/lbm. The piston, with a mass of 110 lbm and cross-sectional area of 0.11 ft2, is in equilibrium with th..
Find the reservoir that the stream of water exiting nozzle : A fire truck draws water from an open constant-level reservoir through a hose of 0.2 ft2 cross section. The water is discharged from the pump through another 0.2 ft2 hose to a surge tank pressurized to 120 psig with air at the top. The pump adds 970 ..
Determine the volume and height of the cooling tower : A counter flow cooling tower cools 2000 gal/min water from 104 F to 85 F with 210,000 ft^3/min of air at 90 F Dry bulb Temperature and 76 F WBT . The Mass transfer coefficient -surface area product is hA= 123lbm/hr ft^3. Air mass flow rate per unit c..
Torsion and direct compression in the base of the boom : A work platform is elevated on the end of a boom that has the ability to extend its length and vary its angle with respect to the ground. The platform width is large compared to the boom diameter so that it is possible to load the boom eccentrically ..
Determine net rate of heat transfer for ambient reservoir : A heat pump supplies 40 kW of heat to maintain the inside of a house at 25 degree C in cold winter months when the ambient temperature is 00C. Power required to operate the heat pump cycle is provided by a heat engine cycle which receives 10 kW of he..
Determine the velocity of the air at the inlet : At steady state, air at 200 kPa, 325 K, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross-sectional areas. The inlet cross-sectional area is 6 cm 2 . At the duct exit, the pressure of the air is 100 kPa and..
Streams of cold and warm air are mixed to get air : In air-conditioning systems, streams of cold and warm air are mixed to get air with the right temperature. Consider a mixing chamber into which cold air enters at 8 degree C and 100 kPa at a rate of 0.55 m3/s and warm air enters at 30 degree C and 10..
Find the sum upto n terms : find the sum upto n terms of the following sequence 3+33+333+... n terms
Determine the voltage of the source : A piston-cylinder device contains 12 kg of saturated R-134a vapor at 3.2 bar. An electric source supplies 8 A current to a resistor within the cylinder for 4 minutes and there is heat transfer of 400 kJ to the system. During these energy interactions..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd