Determine mole fraction of dichloromethane in the gas

Assignment Help Mechanical Engineering
Reference no: EM13639584

We have a process air stream that is 30 mole% dichloromethane and 70% air at 80 oF. The inlet flow rate of the gas stream is 2 liter/min at pressure of 1 atmosphere. The process stream is being sent to a condenser operating at 5 atm and 0 oF to recover the dichloromethane prior to recycle to the process. A pure dichloromethane stream is produced and the product gas stream will be saturated with dichloromethane at 5 atm and 0 oF.

A. Sketch and label process flow diagram for the condenser.

B. Determine the molar flow rate of the inlet gas stream at 80 oF and 1 atm.

C. Determine the vapor pressure of dichloromethane at 0 oF.

D. Determine mole fraction of dichloromethane in the gas product stream.

E. Determine the flow rate of the product gas and liquid stream from the condenser.

F. The immediate dangerous to life and health concentration for human exposure to dichloromethane is 2300 ppm (as tabulated in material safety data sheet, MSDS).

o What is the boiling point temperature for dichloromethane required at atmospheric pressure to achieve this saturation concentration?

o Would it be practical to use condensation as method to reduce concentration of dichloromethane in air to the required limit? Discuss.

Reference no: EM13639584

Questions Cloud

Let x equal to the grade of a student in a stat course : let x equal to the grade of a student in a stat course. suppose that x is nu 100. using the traditional method of
A river flows due east at 150 ms a boat crosses the river : a river flows due east at 1.50 ms. a boat crosses the river from the south shore to the north shore by maintaining a
A manufactured battery is defective with the probability of : a manufactured battery is defective with the probability of 5.in a lot of n200 batteries approximate the probability
A student has a solution containing a mixture of metal : a student has a solution containing a mixture of metal cations cu2 cr2 and fe3 each a solution with no3- anion. adding
Determine mole fraction of dichloromethane in the gas : we have a process air stream that is 30 mole dichloromethane and 70 air at 80 of. the inlet flow rate of the gas stream
An electronic company manufactures resistors that have a : an electronic company manufactures resistors that have a mean resistance of u 100 ohm and a standard deviation s 10
A fireman 500 m away from a burning building directs a : a fireman 50.0 m away from a burning building directs a stream of water from a ground-level fire hose at an angle of
What is the magnitude of the average acceleration of a : a what is the magnitude of the average acceleration of a skier who starting from rest reaches a speed of 11.8 ms when
An artillery shell is fired with an initial velocity of 300 : an artillery shell is fired with an initial velocity of 300 ms at 55.0deg above the horizontal. to clear an avalanche

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd