Determine magnitude-radial frequency-frequency and period

Assignment Help Electrical Engineering
Reference no: EM13286849

Determine the magnitude, radial frequency, frequency, period, and phase for the following waveforms:
(a) i1(t)=10cos(40t+170)A
(b) v2(t)=34sin(380t+40)V

(a)
magnitude = A
radial frequency = rad/s
frequency = Hz
period = s
phase =

(b)
magnitude = V
radial frequency = rad/s
frequency = Hz
period = s
phase =

Reference no: EM13286849

Questions Cloud

What is the net force acting on the car : On vacation, your 1100 kg car pulls a 540 kg trailer away from a stop light with an acceleration of 2.10 m/s2. What is the net force acting on the car
What rate of return is this investment being offer : Begging on your child's 18th birthday, the plan will provide $20,000 per year for four years. What rate of return is this investment being offer?
What force must the drag chute exert on the car : A drag racer crosses the finish line doing 216 mi/h and promptly deploys her drag chute, What force must the drag chute exert on the 850 kg car to slow it to 45.2 mi/h in a distance of 161 m
What was its cost of goods sold : what was its cost of goods sold? a. Assume FIFO inventory accounting b. Assume LIFO inventory accounting
Determine magnitude-radial frequency-frequency and period : Determine the magnitude, radial frequency, frequency, period, and phase for the following waveforms: (a) i1(t)=10cos(40t+170)A (b) v2(t)=34sin(380t+40)V
How far did you travel while braking : Driving home from school one day you spot a ball rolling out into the street. You brake for 1.10 s, How far did you travel while braking
Evaluate the magnitude of the charge : You measure an electric field of 1.26×106 N/C at a distance of 0.149 m. from a point charge.  find the magnitude of the charge
Evaluate the magnitude of the charge : You measure an electric field of 1.26×106 N/C at a distance of 0.149 m. from a point charge.  find the magnitude of the charge
Evaluate the magnitude of the charge : You measure an electric field of 1.26×106 N/C at a distance of 0.149 m. from a point charge.  find the magnitude of the charge

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is rms voltage of source in a single loop series

3) What is the RMS voltage of the source in a single loop series circuit if Irms = 1A-30° and Ztotal = 100 65° 4) What is the power dissipated by an electric heater with a resistance of 20? drawing a current waveform of i(t) = 10 sin(60t) Amps

  Design uv flip-flop using a jk flip-flop and two logic gates

Design a UV flip-flop using a JK flip-flop and two logic gates. where the characteristic table for the UV flip flop is U V Q(t+1) 0 0 1 0 1 !Q(t) 1 0 Q(t) 1 1 Q(t)

  What is the number of uniform quantization levels needed

A signal is quantized using PCM. The maximum signal to quantization noise ratio is 20dB. What is the number of uniform quantization levels needed

  Design dc-coupled differential amp with differential gain

Design a DC-coupled differential amplifier with differential gain of 50 for input signals near ground, supply voltages of +15V and -15V and quiescent currents of 0.1mA in each transistor.

  Where the new system is linear without any approximations

where x is a state variable and r is an input variable. Perform a change of variables in r, i.e., r (t) --> u (t),where the new system is linear without any approximations (hint: assume x (t) ismeasurable)

  Find two vectors that describe the two lines originating

a) Find the intersection of the two lines. b) Find two vectors that also describe the two lines originating from the intersection. c) Find the angle between the two lines.

  Determine the minimum value of transmitter power required

An analog system requires an antenna signal power of 100pW to meet the required detected signal-to-noise ratio. Other system parameters are given as follows: Gt(dB) =4dB determine the minimum value of the transmitter power required.

  Find the charges q1 and q2 due to the repulsive force

The repulsive force one exerts on the other when they are 20cm apart is 1.35 X 10-4 N. after the balls are touched together and then represented once again to 20cm, now the repulsive force is found to be 1.40 X 10-4 N. find the charges q1 and q2.

  Find the receiving antenna gain in order to secure a c-n

In a line of sight link , the transmitted power = 1 watt at the frequency of 11 GHz and the transmitting antenna has gain of 1000 , the receiving antenna is 40 Km apart from the transmitting station

  Find the required number of turns ration of the transformer

It is required to design a full-wave rectifier using a center tapped rectifier to provide an output voltage of 10 v. Find the required number of turns ration of the transformer. Assume that a conducting diode has a voltage drop of 0.7v. The ac lin..

  What is the maximum load possible without a heat sink

A small buck converter has 24 V input and 12 V output. The transistot has Rds(on) = 0.1 Ohms. The diode is modelled as a 1 V drop. Each device has Rtheta(ja) = 40 K/W and Tjucntion

  Compute the line current-power and power factor for the toad

The load on a 460-V, 60-Hz, Y-connected, balance three-phase source consists of three equal Y-connected impedances of 100+j100 ohms, and three equal Delta-connected impedances of 300-j300 ohms. Compute the line current, power, and power factor for..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd