Determine its mass flow rate kgs if the refrigerant flow

Assignment Help Mechanical Engineering
Reference no: EM13645235

Refrigerant 134a at 10 bars, 38oC flows at 10.0 kg/s through a heat exchanger, leaving at 9.0 bars and 80oC. It exchanges heat with a stream of steam entering at 1 bar and 200oC.
Find: i) If the steam leaves the heat exchanger as a saturated vapor at 1 bar, determine its mass flow rate (kg/s). ii) If the refrigerant flow rate is cut to 5.0 kg/s but it still leaves at the same state, and the steam flow rate stays the same, what is the exit temperature of the steam?

Reference no: EM13645235

Questions Cloud

Determine the change in the specific internal energy of : determine the change in the specific internal energy of solid aluminum as it is heated at atmospheric pressure from 300
Calculate the change in enthalpy for the mg hcl reaction : calculate the change in enthalpy for the mg hcl reaction using standard enthalpies of formation delta hf for hcl aq
Vanadium is a transition metal that uses its s an d : when gaseous hf reacts with vcl33 crystals an exchange reaction occurs forming vf3 and a second product that is a gas.
Drops of rain fall perpendicular to the roof of a parked : drops of rain fall perpendicular to the roof of a parked car during a rainstorm. the drops strike the roof with a speed
Determine its mass flow rate kgs if the refrigerant flow : refrigerant 134a at 10 bars 38oc flows at 10.0 kgs through a heat exchanger leaving at 9.0 bars and 80oc. it exchanges
A radioactive substance has a half-life of 465 minutes how : a radioactive substance has a half-life of 46.5 minutes. how many grams of the radioactive substance will remain in a
If 50 mg of phenacetin were dissolved in 100 ml of water : the pain reliever phenacetin is soluble in cold water to the extent of 1.0 g 1310 ml and soluble in diethyl ether to
Determine a the velocity of the center of the bar at this : at the instant shown the angular velocity of the 6kg bar is 10radsec counterclockwise and its angular acceleration is
Find a total strain corresponding to yield strength b what : in a tensile test for an alloy used for ballistic-missile launch tubes on boomer submarines the yield strength was

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd