Determine if the small diameter can be further reduced in

Assignment Help Mechanical Engineering
Reference no: EM13631375

In order to accommodate a bearing on an 80mm diameter shaft it is suggested that it be reduced in diameter to 65 mm with a fillet radius of 2.0 mm at the step. The shaft is intended to transmit 45 kW at a speed of 700rpm with torque transmission in one direction only, running continuously during an 8 hour shift. The bending moment at the step is calculated to be 500 Nm. The shaft is subjected to minor shock loads when the load is suddenly applied and is made from CS1030 shafting steel.

Assume the modulus of rigidity, G, = 80 GPa and use FOS = 2.

a) Determine if the small diameter can be further reduced in diameter by calculating the minimum size based on equivalent torque.

b) Determine the torsional deflection of the 65 mm diameter shaft assuming it to be 1 m in length.

Reference no: EM13631375

Questions Cloud

A non-uniform steady incompressible flow is observed to : a non-uniform steady incompressible flow is observed to have a velocity of 15ms at a point where the cross-sectional
Lght of wavelength 671 nm is incident on a single slit : light of wavelength 671 nm is incident on a single slit. the central bright fringe is 2.60 cm wide on a flat screen
The intention is to draw air from the receiver during the : a stoped out area with a volume of 20000 m3 is to be used as a receiver. it is to be charged to an absolute pressure of
A thin layer of oil of refractive index 118 is spread on : a thin layer of oil of refractive index 1.18 is spread on the surface of water n1.33. if the thickness of the oil is
Determine if the small diameter can be further reduced in : in order to accommodate a bearing on an 80mm diameter shaft it is suggested that it be reduced in diameter to 65 mm
The interference pattern shows a peak at the center of the : two slits separated by a distance of d 0.185 mm are located at a distance of d 2.06 m from a screen. the screen is
A 356 mm diameter main services a section of a mine and : a 356 mm diameter main services a section of a mine and carries 4.8 kgs of compressed air at peak periods. if the main
One bright summer day a swimmer is floating with her head : one bright summer day a swimmer is floating with her head just above the surface of a large lake where the water has
The atomic ratio of uranium-235 to uranium-238 in current : two billion years ago a uranium deposit in oklo africa spontaneously underwent nuclear fission. this was determined by

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd