Determine how many holes are in the valence band

Assignment Help Electrical Engineering
Reference no: EM13288683

At room temperature in a cubic centimeter of intrinsic siliconthere will be about 10 billion electrons in the conduction band
a)How many holes are in the valence band
b)If electrons are constantly seeking lower energies and recombining with holes then how can the number of 10billion remain constant.

Reference no: EM13288683

Questions Cloud

Which of these projects is worth pursuing : Which of these projects is worth pursuing?
Find the pun as a dual of the pdn in complete realization : (a) Give the Boolean function Y . (b) Sketch a PDN directly from the expression for Y. Note that it requires 12 transistors in addition to those in the inverters (c) From inspection of the PDN circuit, reduce the number of transistors to 10
Compute the amount of heat required to raise : Calculate the amount of heat required to raise the temperature of 100.0g of water from -0.10 C to +0.10 C
Find the number of electrons passing through the device : The current supplied by a battery in a portable device is typically 0.131 A. Find the number of electrons passing through the device
Determine how many holes are in the valence band : a)How many holes are in the valence band b)If electrons are constantly seeking lower energies and recombining with holes then how can the number of 10billion remain constant.
Explain what is the final mass upon mixing of hcl : what is the final mass upon mixing 8.54 mL of HCl and 8.54 mL of NaOH, both solutions have an initial concentration of 2.00 M.
Discussion typical reasoning : Discussion Typical Reasoning
How much charge does each capacitor carry : Three identical capacitors are connected in parallel to a battery. If a total charge of Q flows from the battery, how much charge does each capacitor carry
How to calculate the absorbance at ph : A solution of a weak acid, HA, is prepared by dissolving 4.8 mmol of HA in 10.0 liters of a solution.The following values of absorbances were measured in a 1.0 cm cell in various buffers.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the flux density and voltage supplied

A magnetic circuit constructed of sheet steel has an average length of 1.3 m and a cross sectional area of 0.024msq. a 50 turn coil wound on the ring has a resistance of .82ohms and draws 2a from a dc supply.

  Determine the conductor size for each motor tap

Determine the conductor size for each motor tap, the motor controller size, overload rating, motor and controller disconnect rating, time-delay fuse rating, and motor branch circuit conductor size.

  Calculate the resistance of the coil of copper wire

A coil made of 150 turns of copper wire wounded ona cylindrical coil . If that means radius of the turns in 6.5mm and the diameter of the wire is 0.4mm, calculate the resistance of the coil.

  Describe the operation of the series rl circuit

The discussion must address phase angle relationships of current and voltage. The answer must include the effect of source frequency on the voltage drolps across the resistor and the inductor at very loave and very high frequency values.

  Write a function that accepts as input arguments a vector x

(a) Write a function that accepts as input arguments a vector x and two scalars m and s and plots the function g(x) = [1/(s*sqrt(2*pi))]*exp[(1/2)*((x-m)/s))^2] (b) Using the above function, plot y(x) for a vector x -5 to 5, m = 0 and s = 1

  Find the output frequency when the input frequency

A system samples a sinusoid of frequency 480 Hz at a rate of 100 Hz and writes the sampled signal to its output without further modification. Determine the frequency that the sampling system will generate in its output.

  Use the interrupt-driven approach

Store the arrival times in memory locations starting from $1000.(Do this is in C. Store the results in an array and don't worry about the speci c location of the results.)

  Determine what is the average minority carrier lifetime

A light source generates 10^17 electron hole pairs per cm^3 persecond in an n-type sample doped ND = 10^16 cm^-3 and the average minority carrier lifetime is 10^-5 seconds. Is this Low level injection.

  Find the values of l and c and the cutoff frequencies

Design a series resonant circuit to have a bandwidth of 400 Hz using a coil with a Ql of 20 and a resistance of 2-ohm. Find the values of L and C and the cutoff frequencies

  Find the input impedance into this line at z

A transmission line with no loss, with Z0= 60 ohms, is operated at 60MHz. The velocity on the line is c. The line is soldered to a ground connection at z=0. Find the input impedance into this line at z= -1.25 meters

  Find the actual solution using the inverse laplace transform

Transfer function in s t = [0-2*Ts : Ts : Tmax] ; Find the actual solution using the inverse laplace transform syms ycont ycont = ilaplace(Gs,t) Sampling times of 0.01, and simulation runs for 10 seconds

  Design a circuit that implements the function with vhdl code

Use a K-Map to design a circuit that will accept 5-bit input, and output the value left-shifted by 1. For example, if the input is 10101, the output is 01010. Design a circuit that implements this function. Write the VHDL code.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd