Determine how many different layouts are possible

Assignment Help Electrical Engineering
Reference no: EM13225433

In a layout of a printed circuit board for an electronic product, there are 12 different locations that can accommodate chips.

(a) If five different types of chips are to be placed on the board, how many different layouts are possible?
(b) If the five chips that are placed on the board are of the same type, how many different layouts are possible?

Reference no: EM13225433

Questions Cloud

Explain the dichloroethene layer turns dark orange : A student substitutes his unknown for the NaBrO3. The dichloroethene layer turns dark orange. Which ions could be ruled out and what test should be performed next?
Describe the different types of interviews : Describe the different types of interviews, and some problems encountered in interviewing.
Seeking goodwill businesses : rite a short essay about seeking goodwill businesses – include why it is important for both an established business as well as a new business. How is communication similar and different in these two situations?
How can quality management concepts support sustainability : How can quality management concepts support sustainability efforts? What are some examples?
Determine how many different layouts are possible : (a) If five different types of chips are to be placed on the board, how many different layouts are possible (b) If the five chips that are placed on the board are of the same type, how many different layouts are possible
Compute the wavelength of the n=4 to n=1transitions : Calculate the wavelength of the n=4 to n=1 and the n=4 to n=3 transitions. Indicate in which regions of the electromagnetic spectrum these transitions would occur.
What is the business process for apple inc : What is the business process for Apple Inc? Can this process be improved to better meet customer needs? Analyze the process using the DMAIC (define, measure, analyze, improve, control) methodology.
How parameters must be constrained to make system constant : In the question below only focus on the parameter or parameters that are relevant to the particular property you are being asked about in the particular question. If you need to constrain a parameter to satisfy the stated criterion.
Evaluate the effectiveness of the different techniques : Discuss the techniques used by two of the practitioners/writers studied on the module in adapting classical plays to a contemporary context. Evaluate the effectiveness of the different techniques

Reviews

Write a Review

Electrical Engineering Questions & Answers

  A unit for a telecommunications system is to be designed

A unit for a telecommunications system is to be designed so as to have a minimum availability of 0.9994. The MTTR (mean time to repair) for the unit is estimated to be 24 hours.

  Explain what will the new mean and variance

Maximum Likelihood to get the above parameters i.e. u0 and var. Now from these 999 points, I take one point out (lets call it i) and add a new point (lets call it j). What will the new mean and variance be?

  What is the total number of electrons transported

What is the total number of electrons transported from the positive electrode to the negative electrode by the charge escalator from the time the battery is first used until it is completely dead?

  Basic neutralizer control system

Write a short report that analyses the P&ID - Basic Neutralizer Control System: The neutralizer process may be used to adjust the pH of a feed stream.

  Explain what is the resolution of each quantizer

Supply the quantisation levels (including zero) that are available. Do this for both the three and 4-bit ADC in table form. What is the resolution of each quantizer?

  Calculate the total complex power

Calculate the total complex power, total current drawn and the total power factor and Y-connected load with an impedance of (1+ j 6) ohm per phase,

  Calculate the s/n ratio for a receiver output

Calculate the S/N ratio for a receiver output of 4 V signal and 0.48 V noise both as a ratio and in decibel form. (69.44, 18.42dB)

  Calculate the traffic load per cell

The system uses a 7-cell reuse pattern. If the offered traffic per user is 0.03 Erlangs and the average number of calls per hour per user is 1.5, for an Erlang-C system with a probability of delaying a call being 5%, calculate the traffic load per..

  Explain baseband digital trnamission and multi level coding

Baseband digital trnamission and multi level coding, A baseband digital data link transmits polar binary NRZ current pulses at a rate of 1.0 Msps. The link uses ideal RRC filters with roll off factor r = 0.5.

  Ziegler-nichols open loop tuning

Ziegler-Nichols Open Loop Tuning Often, when working with a faster loop, many people will opt only for a PI control philosophy

  Design the combinational logic circuit for an elevator

Design the combinational logic circuit for an elevator controller such that the option to go up or down by only one floor is disabled. Assume that the building the elevator is in has 4 floors. Your inputs are the current floor and the next request..

  Define what is transmission velocity and how it is different

what is transmission velocity and how it is different from drit velocity. Drift velocity the actual (physical) velocity of electrons along the wire.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd