Determine gamma-ie and ib for the transistor

Assignment Help Electrical Engineering
Reference no: EM13282456

A p_n_p common base transistor is biased in the forward active modewith beta=60 and IC= 0.85 mA. Find gamma, IE,and IB for this transistor.

Reference no: EM13282456

Questions Cloud

What is the annual percentage rate on your account : Your credit card company charges you 1.13 percent per month. What is the annual percentage rate on your account?
Define much heat is required to raise the temperature : How much heat is required to raise the temperature of a mole of oxygen from 298 to 3000 K at constant pressure
Find the expression for the total equivalent capacitance : Find the expression for the total equivalent capacitance for an array of n capacitors with arbitrary capacitance C1,C2,...,Cn; when they are connected a) inseries and b) in parallel.
What is the length of the fiber : Gold, which has a density of 19.32 g/cm3, is the most ductile metal and can be pressed into a thin leaf or drawn out into a long fiber. what is the length (in m) of the fiber
Determine gamma-ie and ib for the transistor : A p_n_p common base transistor is biased in the forward active modewith beta=60 and IC= 0.85 mA. Find gamma, IE,and IB for this transistor.
State solid iron(ii) hydroxide decomposes to form solid iron : Write the balanced chemical equation for the following reaction. Phases are optional. Solid iron(II) hydroxide decomposes to form solid iron(II) oxide and liquid water.
What is the opportunity cost of your decision : Would you drive there and buy it, how does your decision benefit you and what is the opportunity cost of your decision?
Obtain the potential difference across each capacitor : Two capacitors are connected in series. Let 3.40mF be the capacitance of first capacitor, Calculate the potential difference across each capacitor
Define the temperature of a mole of oxygen : How much heat is required to raise the temperature of a mole of oxygen from 298 to 3000 K at constant pressure. The book gives the following values for Cp (specific heat at constant pressure): 29.376 J/(K*mol) at 298 K and 39.884 J/(K*mol) at 3000 ..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the output signal for the input signal of a system

The transfer function of a system is formulated as H(f)=2f^2+i3f+2. Calculate the output signal for the input signal below which was applied to this system Vin(t)= 5+2cos(20(pi)t+30degrees)+sin(10(pi)t)

  Compute what is the average power of the quantization noise

Consider the following discrete-time signal where the samplesare represented using N bits. a. How many bits are needed to ensure that the quantization levelis less than 0.001. b. Suppose N = 8 bits. What is the average power of the quantization noise..

  Design system of two additional lense that would change beam

An optical signal from a modulator can be sent to multiple channels by the LCSLM. This; however, requires that the beam size from the AM is adjusted to match the size of the SLM area. Assume that both lenses in an AM setup are identical

  Calculate and display the voltage for each resistor

The voltage of a resistor is calculate by the Ohm`s Law: V = R I. write a program that will input resistance R, current I for several resistors, and will calculate and display the voltage for each resistor.

  Determine what is the dc voltage from a full wave rectifier

The radial field is provided by the coils in the stator to obtain a flux density of .2 Wb/m^2 so that there is one south and on the opposite side, the north pole. The coils on the rotor, 10 turns per coil, are connected in series through the commu..

  Explain autocorrelation and tao

Autocorrelation and Tao, question from my ECE 302 class regarding the mean of a random process given a particular autocorrelation function in terms of tao.

  Find what voltage will be across the capacitors

A 3uF capacitor is charged to 100 V. If it is the connected in parallel with a 10 uF capacitor, what voltage will be across the capacitors

  What is the signal-to-noise ratio of the spread signal

Suppose that a voice signal normally occupies 30 kHz of bandwidth and has a signal-to-noise ratio of 20 dB. Spread-spectrum techniques are used to increase its bandwidth to 2 MHz. (a) What is the signal-to-noise ratio of the spread signal

  Derive equations for the electric flux density for all ?

Given a coaxial cable with solid inner conductor of radius a, an outer conductor that goes from radius b to c (so c>b>a), a charge +Q that is assumed evenly distributed throughout a meter length of the inner conductor

  What is the main difference between the two cases

Two dc motors are compared. the first one is a 4hp dc motor which draws a current or 0.7A when the field is connected to a 150V source. the second, a 600 hp motor draws a field current of 5A when the field is connected to a 300V dc source.

  What frequency of the siren does a person in the car hear

A car is traveling on a street at 24.6 m/s. An ambulance is behind the car, moving in the same direction and with a speed of 38.7 m/s. The siren on the ambulance is emitting sound at a frequency of 1575 Hz. The speed of sound in the air is 343 m/s..

  What is the value of the instantaneous voltage

1. A sinusoidal waveform is described by the equation: v(t) = 20V sin(120pit) pi = 3.1416 What is the value of the frequency 2. A sinusoidal waveform is described by the equation

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd