Determine for each case the ration of the total energy

Assignment Help Civil Engineering
Reference no: EM13545653

Consider two cases: (1) a constant wind velocity that is twice the mean wind velocity and operating half the time; and (2) a constant wind velocity that is three times the mean wind velocity operating one-third of the time. At all other times, the wind velocity is zero. Determine for each case the ration of the total energy available from the wind to the total wind energy available at the mean velocity operating continuously.

Reference no: EM13545653

Questions Cloud

Determine the magnitude of the largest elastic load p that : The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. the outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. if the yield stress for the steel is
What is the maximum weight of the crate that the system can : Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of = 74.0 with the floor and rope segment CD
Find the capacity of the column with 1% reingforcement : A circulatr concrete column with a diameter of 8" has spiral reinforcing. Find the capacity of the column with 1% reingforcement. Find the capacity of the column with 8% reinforcement.
Sketch how you will place the bars and calculate : Concrete cover on both sides. Sketch how you will place the bars and calculate the location of the effective depth. Place as many bars in the lower layers as possible.
Determine for each case the ration of the total energy : Consider two cases: (1) a constant wind velocity that is twice the mean wind velocity and operating half the time; and (2) a constant wind velocity that is three times the mean wind velocity operating one-third of the time. At all other times, the wi..
Design a one way slab to support a uniform live load : Design a one way slab to support a uniform live load of 300 psf. The beam is simply supported with a span of 20 ft. Use a reinforcement ration ( Ps) of 0.008 Use f'c=3000 psi and fy=60000 psi.
The angle measured counterclockwise between line ab and : The true azimuth of line AB is 193 degrees 20'. The angle measured counterclockwise between line AB and another line AC is 205 degrees 10'. The true azimuth of line AC is:
What is the elevation of point n : A leveling rod is held vertically on another point N. When a sight is taken on the rod, the telescope is inclined so that the horizontal cross line of the transit intersects the rod at a reading of 4.9 ft.
What was the difference in elevation between the two points : A rod was held on point B and the telescope is inclined so that the horizontal cross line of the transit intersects the rod at the 5.2 ft mark.If the reading on the vertical limb of the transit was +25° 19’, what was the difference in elevation betwe..

Reviews

Write a Review

Civil Engineering Questions & Answers

  With this method approximately 80liters of water are require

A meat packing plant manager is trying to decide between twodifferent methods for cooling cooked hams. the spray methodinvolves spraying water over the hams until the ham temperature isreduced to 30 degrees Celcius. With this method approximately 80l..

  How many moles of water condense per cubic meter of feed gas

Suppose a sample of the 90 °C air is put in a closed variable-volume chamber containing a mirror, and the pressure is raised at constant temperature until a mist forms on the mirror. At what pressure would the mist form

  Factors of safety against sliding and against overturning

Determine the factors of safety against sliding and against overturning, and also the soil pressure at the heel and toe. Assume hydrostatic uplift varies uniformly from full hydrostatic head at the heel of the dam to zero at the toe. consider 1m l..

  Determine dilatation and change in volume of the 200m length

determine the dilatation and change in volume of the 200mm length of the rod if A) the rod is made of steel E=200 Gpa v=.30 B)the rod is made of aluminum E=70 Gpa v=.35.

  Find all contact forces to the contacting surfaces

Cylinders A & B weigh 500N each and cylinder C weighs 1000N. Assuming frictionless contact between all surfaces, find all contact forces. Diameters A&B= 1, C=2. Frictionless contact means forces are normal to the contacting surfaces.

  What is the rate of fuel used by the engine in the test

A container of petrol on a set of scales is used to measure the rate at which fuel is used by an engine under test. In one test the weight measured by the scales decreases by 25.0 N in 1 hour.

  Calculate deformation of truncated equilateral steel pyramid

Calculate deformation of the truncated equilateral triangular steel pyramid. The pyramid has the height h of 156mm truncated at the top by 2mm and the base side s of 127mm.

  Explain why would it be dangerous to use the material

A structural component in the form of a very wide plate is to be fabricated from 4340 steel that was cooled using a fast cooling rate and has a yield strength of 1515 MPa and a fracture toughness (KIC) of 60.4MPam.

  What distance must be cleared from the inside edge

design a horizontal curve with a 40-degree central angle ( delta = 40) for a two-lane road with 11-ft lanes. The design speed is 70 mi/h and superelevation is limited to 0.06 ft/ft. Give the radius, degree of curvature, and length of curve that yo..

  What is the estimated uncertainty in the length of vector

The base line vector between the base and roving reciever is 8340m and has an accuracy of +/-(1to 2 cm +/-2ppm). What is the estimated uncertainty in the length of this vector

  Draw a footing detail showing all pertinent design parameter

design a square individual footing to support a 16 inch square reinforced concrete column. service loads include a dead load of 180 kips and a live load of 140 kips. both column and footing have fc=3000psi and fy=60000 psi.

  Find the principle stresses and max shearing stresses

A circular beam length 36 inches and diameter 1 inch is supported on the left end by a pin joint and the right end with a roller. The beam is under axial tension with forces of 1000 lbs out of each end.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd