Determine expressions for the local and convective

Assignment Help Mechanical Engineering
Reference no: EM13639087

The velocity in a two-dimensional flow field is given by the equation: V = i2xt - j2yt where the velocity is in m/s when x, y, and t are in metres and seconds respectively and i and j are unit vectors in the x and y directions respectively. Determine expressions for the local and convective components of acceleration in the x and y directions. What is the magnitude and direction of the velocity and acceleration at point x = y = 2 m at t = 0?

Reference no: EM13639087

Questions Cloud

A jet fighter plane is launched from a catapult on an : a jet fighter plane is launched from a catapult on an aircraft carrier. it reaches a speed of 42 ms at the end of the
If all you care about is that the battery purchased lasts : you are planning on junking your old car after it runs an additional 30000 km. the battery on this car has just failed
A wind is blowing with a speed of 250 kmh from the south : a commercial aircraft is going from jfk airport to ohare airport at a cruising speed of 650 kmh measured relative to
A carnot heat pump operates between an outdoor temperature : a carnot heat pump operates between an outdoor temperature of 258 k and an indoor temperature of 283 k. find its
Determine expressions for the local and convective : the velocity in a two-dimensional flow field is given by the equation v i2xt - j2yt where the velocity is in ms when x
Assuming 25 drops per milliliter determine the initialmolar : nbsp1.0-ml volume of .010 m h2so3 is added to amixture of 12 drps of .01 m hio3 8 drops of deionized water and 1drop of
An electron and a proton are each accelerated through a : an electron and a proton are each accelerated through a potential difference of 21 million volts. find the momentum in
An experimenter has prepared a drug dosage level that she : for the following problem i have solved a through c and used a summation of combinations to solve for alpha 0.009982 i
Calculate the friction force on a walking 750 kg astronaut : the acceleration due to gravity on the moon is 1.62 ms2.1. calculate the friction force on a walking 75.0 kg astronaut

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the initial value of n is 1 millionl what values of k

suppose the rate of growth of a bacterial population n cellsliter is described by dndt kn -1000. the terms represent

  What is the ideal mechanical advantage of the system

A wheel barrow is used to lift a 200 lb load. The length from the wheel axle to the center of the load is 2 ft. The length from the wheel and axle to the effort is 5 ft. 5. What is the ideal mechanical advantage of the system?

  Plot thrust vs time what is the velocity of the rocket at

a rocket has an initial mass of 25000 kg of which 20000 kg is fuel and oxygen. it is propelled directly upward from

  A 6-lb block is attached to a cable and to a spring

a 6-lb block is attached to a cable and to a spring vertically the cable above and the spring below. the spring

  How to convert the uneven diameter of the hollow tube in to

a solid hollow tube thin wall with pin in the bottom and the top part is connect with another tube and there is a force

  An industrial water shutoff valve is designed to operate

an industrial water shutoff valve is designed to operate with 30lbs of force and will encounter 200lbs of resistance

  A mass of 55 kg is suspended from a spring of stiffness 835

a mass of 55 kg is suspended from a spring of stiffness 83.5 kgcm. a dash pot is fitted and it is found that the

  Determine the x-component and the magnitude of force

the y-component of the force f which a person exerts on the handle of the box wrench is known to be 320newton. determine the x-component and the magnitude of force.

  Air flows steadily through an adiabatic non-ideal turbine

air flows steadily through an adiabatic non-ideal turbine entering at 150 psia 900degf and 350 fts and leaving at 20

  Define the final state inside the tank

Find the final state inside the tank, A tank contains 2kg of nitrogen at 10K with a quality of 50%.Through a volume flow meter and valve, 0.5kg is now removed while the temperature remains constant.

  Determine the centerline temperature of the beam after an

a cylindrical stone mix concrete beam of diameter d 0.45 initially at ti 20c is exposed to hot gases at tinfinity

  All four sides of the plate are maintained at 20 degree c

a 50-cm by 50-cm plate of pure nickel generates 3.9 mwm3 of energy uniformly within the plate. all four sides of the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd