Determine estimated unknown speed if the data were obtained

Assignment Help Civil Engineering
Reference no: EM13296747

In an attempt to estimate the speed of a vehicle just before it hit a traffic signal pole, a traffic engineer measured the length of the skid marks made by the vehicle and performed trial runs at the site to obtain estimate if the coefficient of friction, Determine the estimated unknown speed if the following data were obtained:
Skid Marks Length: 585, 590, 580, 595 (in feet)
Speed of trial run: 30 mph
Distance travelled during trial run: 300 ft
Examination of the vehicle just after the crash indicated that the speed of impact was 35 mph.

Reference no: EM13296747

Questions Cloud

Evaluate how or why the business made such a mistake : Why is knowing (or estimating) the product demand so crucial for a firm? In your response, include an example of a U.S. business that has suffered from poorly estimating the demand of its products.
Organisms in the original undiluted culture : What was the viable count of organisms in the original undiluted culture?
Design the ramp for the highest horizontal curve : The entrance to Mt. Hood Meadows (elevation 3,075 ft at the point of crossing) is grade separated from Viking highway (elevation 3,050 ft at the point of crossing) and will have to be connected. The two roadways intersect at a right angle.
From the e-activity : Consider a long-term debt you currently own (e.g., a mortgage or student loan) and discuss how you would take present value into account when deciding whether you should retire that debt ahead of schedule. Explain your rationale.
Determine estimated unknown speed if the data were obtained : In an attempt to estimate the speed of a vehicle just before it hit a traffic signal pole, a traffic engineer measured the length of the skid marks made by the vehicle and performed trial runs at the site to obtain estimate if the coefficient of f..
What is schulers new equilibrium price : Assume that rRF and rM are equal to the values in part c. After all these changes, what is Schuler's new equilibrium price? (Note: D1 goes to $2.34.) Round your answer to the nearest cent.
Determine speed at which student conducted her experiment : A student is trying to test the braking ability of her car determined that she needed 18.5 ft more to stop her car when driving downhill on a road segment of 5% grade than when driving downhill at the same speed along another segment of 3% grade.
What is the resistance of each device : An 1800W toaster, a 1.3kW electric frying pan, and a 120 W lamp are plugged into the same 35A, 140V circuit. what is the resistance of each device
Explain how many g or hcl also reacted : Given the following balanced chemical equation Ca(OH)2+2HCl-->CaCl2 +2H2, if 56.7g of calcium hydroxide react completely, how many g or HCl also reacted

Reviews

Write a Review

Civil Engineering Questions & Answers

  What should be the minimum radius of curvature p

what should be the minimum radius of curvature p for the track at B so that the passengers do not experience a normal force greater than kmg?neglect the size of the car and passengers.Take k=4

  What are the concentrations of cl- and br-

AGNO3 is added to a solution containing 0.001 mol Cl- amd 0.001 mol Br- per liter. What are the concentrations of Cl- and Br- remaining when AgCl just begins to precipitate?

  Mass flow raw through the nozzle

Air enters an adiabatic nozzle steadily at 300 kPa, 200 o C, and 30 m/s and leaves at 100 kPa and 180 m/s. The inlet area of the nozzle is 80 cm 2 . Determine (a) the mass flow raw through the nozzle, (b) the exit temperature of the air, and (c) the ..

  Calculate the force

Calculate the force (in Kn) a punch press must exert if it is to punch out a large washer from a strip of 5-mm thick sheet steel with an ultimate shear strength of 400 MPa. The washer dimensions are as follows: hole diameter is 27 mm. outside diam..

  Atual discharge of a water pipeline

If the elevation difference between the water surfaces is y = 25 + x/11 metres, what minimum pipeline diameter will be required to convey the design discharge? Once your design is complete, determine the actual discharge. The value of x equals 23.

  Construction area skids into a stack of concrete barriers

A car travelling at 60 mph in a construction area skids into a stack of concrete barriers. Skid marks leading to the crash measures 150 ft .

  Find the rate of change in volume

A water tank has a height of 120m, and its area of cross-section is 2000m. Water is released from the tank and the water level drops by 1 meter every minute. Find the rate of change in volume.

  Average shearing stress

Two strips of a plastics material are bonded together as shown. The average shearing stress in the glue must be limited to 1000 kpa.

  Ratio of the magnitude in uniform electric field

What is the ratio of the magnitude of E2 to the magnitude of E1? You may neglect the effects of gravity on the proton.

  Describe the measurements that would have to be taken

describe the measurements that would have to be taken and the equations that would have to be used to determine G23, V32, and E2 for a specially orthotropic transversely isotropic material from a single tensile test.

  Drawing the shearing force diagram

Draw the shearing force diagram and the moment diagram of the following problem. The beam is indeterminate. You need to integrate the moment twice to get a formula for the deflection v(x).

  Hydraulic radius of the river

In that season, what are the hydraulic radius of the river, its mean velocity and volumetric discharge?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd