Determine equation in terms of final velocities of two disks

Assignment Help Mechanical Engineering
Reference no: EM13714082

Disk A has a mass of 5 kg and disk B has a mass of 6 kg. They have the initial velocities shown in the figure. The coefficient of restitution between the disks is e = 0.4.

a) Using the conservation of momentum, determine an equation in terms of the final velocities of the two disks.

b) Using the coefficient of restitution, determine an equation in terms of the final velocities of the two disks.

c) Determine the velocity of disk A just after the impact.

d) Determine the velocity of disk B just after the impact.

Reference no: EM13714082

Questions Cloud

Analysis for both pinion and gear-hardness values : A cable drum for a crane is to rotate between 160 and 166 rpm. Design a gear drive for 25 hp in which the input pinion rotates at 925 rpm and the output rotates with the drum. The crane is expected to operate with a 50% duty cycle for 120 hours per w..
Determine the rate of heat transfer to the rods in the oven : Long cylindrical steel rods (p=7833kg/m3 and cp=0.465kJ/kg*°C) of 8-cm diameter are heat treated by drawing them at a velocity of 4m/min through an 8-m-long oven maintained at 900°C. If the rods enter the oven at 25°C and leave at 750°C,
Find the horsepower to circulate the flow : Consider a recalculating flow in the power cycle shown in the figure. The fluid flowing in 100 ft of smooth pipe have an average specific weight of 50 lbf/ft3 and average dynamic viscosity of 5×10-4 lbf.s/ft2. Head loss in the nuclear reactor is 75 f..
Determine the velocity of the air at the inlet : At steady state, air at 200 kPa, 325 K, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross-sectional areas. The inlet cross-sectional area is 6 cm2. At the duct exit, the pressure of the air is 100 kPa and t..
Determine equation in terms of final velocities of two disks : Disk A has a mass of 5 kg and disk B has a mass of 6 kg. They have the initial velocities shown in the figure. The coefficient of restitution between the disks is e = 0.4.
Coefficient of kinetic friction between train car wheels : A train car has a mass of 17500 kg and is travelling at 10 m/s to the right on a horizontal track. At the same time, another train car with a mass of 12500 kg is travelling on the same track at 6 m/s in the opposite direction. The coefficient of kine..
Determine the velocity of the block the instant : The 20 kg block is falling and when it is 7.5 m from the gravel surface it has a velocity of 2.5 m/s. Determine the velocity of the block the instant it hits the gravel surface using
Determine the heat transfer input required for the heat : A Carnot heat engine produces power of 2.5 kW. It rejects heat to a river that is flowing at 2 kg/s, resulting in a temperature increase of 2° C. The average temperature of the river is 20° C.
Amplitude of the excitation provided to the machine : A 45 kg machine is mounted on a spring of stiffness 8x10^5 N/m. When the machine is set to vibration by a 32 Hz excitation, the machine's amplitude is measured as 1.5mm. What is the amplitude of the excitation provided to the machine? Ignore damping ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd