Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
for a Si conductor of length 5um, doped n-type at 10^15 cm^-3,calculate the current density for an applied voltage of 2.5 Vacross its legth. how about for a voltage of 2500V the electron and hole mobilities are 1500 cm^2/V-s and 500 cm^2/V-s,respectively, in the ohmic region for electric fields below 10^4V/cm. for higher fields, electrons and holes have a saturation velocity of 10^7 cm/s.
Thickness is to be reduced in three steps in a hot rolling operation. Each step will reduce the slab to 75% of its previous thickness. It is expected that for this metal and reduction, the slab will widen by 3% in each step.
determine the values of the external resistors for a 555 timer used as an astable multivibrator with an output frequency of 2 kHz, if the external capacitor C is 3.0 mf and the duty cycle is to be approximately 75%
Activation of a switch at t = 0 in a certain caused the voltage across a 20-mH inductor to exhibit the voltage response V(t) =4e-0.2t mV ( for t ≥ 0) determine i(t) for t ≥ o given that the energy stored in the inductor at t = ∞ is 0.64 mJ.
Design a regulated DC power supply. You will have for input a 110 V input source at a frequency of 60 Hz. The Zener diode to use is the 1N4733A (which is available in the lab). The output voltage is to be 5.1 V with a load resistance above 2.2K.
The coefficient of coupling between two coils is 0.45. The first coil has an inductance of 75 mH and the second coil has an inductance of 105 mH. What is the mutual inductance between the coils
A voltage v(t) = 24cos(2000t-45°)V is applied across a parallel connection of a 5-kΩ resistor and a 100-nF capacitor. Find the steady-state current i_c(t) through the capacitor and the steady-state current i_R(t) through the resistor.
Design a noninverting amplifier with gain of 20. Maxium opamp output current of 0.5 mA should occur for maximum outputvoltage of 8 V.
Make a table showing Temperature as a function of pressure for Psat from 20 to 600 psia every 20 psi, and another table showing pressure as a function of temperature from 150 degrees to 350 degrees every 20 degrees.
Assume a thermocouple generates a linear voltage from 20 mV to 50 mV when the temperature changes from 750 degrees F to 1250 degrees F. How much voltage will be generated when the temperature of the thermocouple is at 1000 degrees F
Calculate the composition of HgxCd1-xTe which can be used for a night vision detector with bandgap corresponding to a photon energy of 0.1 eV. Bandgap of CdTe is 1.6 eV and that of HgTe is -0.3 eV at low temperatures around 4 K.
In a power supply, a 150 microfarad capacitor was connected in parallel with a 200 kOhm resistor. The capacitor was maintained at a charge level of 350 volts DC. After power was removed for ten seconds, someone god a shock from touching the termin..
A voltage source V(t)=100cos(6Π109t - 45(degrees))(V) is connected to a series RLC circuit. If R = 10MΩ, C = 100pF, and L = 1H, use phasor notation to find the following: a.) i(t) b.) Vc(t) (voltage across capacitor)
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd