Determine e the second-law efficiency of the cycle and the

Assignment Help Mechanical Engineering
Reference no: EM13633110

A four-cylinder, four-stroke, 1.8-liter modem, highspeed compression-ignition engine operates on the ideal dual cycle with a compression ratio of 16. The air is at 95 kPa and 70°C at the beginning of the compression process and the engine speed is 2200 rpm. Equal amounts of fuel are burned at constant volume and at constant pressure. The maximum allowable pressure in the cycle is 7.5 MPa due to material strength limitations. Using constant specific heats at 1000 K, determine (a) the maximum temperature in the cycle, (b) the net work output and the thermal efficiency, (c) the mean effective pressure, and (d) the net power output. Also, determine (e) the second-law efficiency of the cycle and the rate of exergy output with the exhaust gases when they are purged.

Reference no: EM13633110

Questions Cloud

What was the initial negative charge on one of the spheres : two identical conducting spheres fixed in place attract each other with a force of 0.112 n when their center to center
What if any assumptions are needed before the t inferential : which factors are relevant to the time a consumer spends looking at a product on the shelf prior to selection? an
A 150g block is launched up a 500 degree ramp using a : a 150g block is launched up a 50.0 degree ramp using a spring compressed a distance of 5.0cm from its equilibrium
When 950g of an unknown metal are submerged in water in a : when 95.0g of an unknown metal are submerged in water in a graduated cylinder the waterlevel rises from 32.2 ml to 49.5
Determine e the second-law efficiency of the cycle and the : a four-cylinder four-stroke 1.8-liter modem highspeed compression-ignition engine operates on the ideal dual cycle with
But from the faucet to the outlet the water is all moving : if the faucet has a constricted opening then the water may speed up there. but when it enters the hose which is larger
A golfer uses a club to hit a 45-g golf ball resting on an : a golfer uses a club to hit a 45-g golf ball resting on an elevated tee so that the golf ball leaves the tee at a
Ethylene diamine tetra-acetic acid edta is awater-soluble : ethylene diamine tetra-acetic acid edta is awater-soluble compound that readily combines with metals such ascalcium
Find the probability the component will fail before t 2 : suppose that the failure time distribution for a product can be approximated by a normal distribution with mu 3 and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd