Determine coil and resistor voltage and overall power factor

Assignment Help Electrical Engineering
Reference no: EM13249856

A coil with an impedence of 64.1 angle 51.4 degrees is connected in series with a resistance 22.5 ohms. The combination is supplied by 120 V source. Determine the coil and resistor voltages and the overall power factor. Draw the phasor diagram for these voltages.

Reference no: EM13249856

Questions Cloud

Determine the optimal number : Determine the optimal number (0, 1, 2, 3, 4, 5, 6) of rooms that the Zigus hotel should overbook in order to minimize average daily costs.
Determine circuit power factor and draw impedence phasor : A coil is placed in series with a resistance of 30 ohms. When the combination is connected to a 220 V, 60 Hz source, the current is 4.2 A and the power drawn by the circuit is 670 W.
Find the direction of the minimum magnetic field : A wire has a mass per unit length of 0.500 g/cm. what is the magnitude and direction of the minimum magnetic field
Optical microscopy and scanning electron microscopy : Compare and explain the reason(s) for the difference in image magnification levels between optical (light) microscopy and scanning electron microscopy. What is meant by “sample charging”, with electron microscopes and why is it an issue?  How can it ..
Determine coil and resistor voltage and overall power factor : A coil with an impedence of 64.1 angle 51.4 degrees is connected in series with a resistance 22.5 ohms. The combination is supplied by 120 V source. Determine the coil and resistor voltages and the overall power factor.
Draft a mission statement for willowbrook school : Draft a mission statement for Willowbrook School, based on information provided in the first two chapters and does a strong business case exist in the case of Willowbrook School? Discuss why or why not.
What advancement in operations management in other countries : Why has it become so important for companies to become competitive in the global business environment?
Find the change in momentum of the ball : a falling rubber ball bounces off the floor. the velocity just before it hits the floor is Vi= (2.7m/2) x + (5.2m/s)y. what is the change in momentum of the ball from just before to just after it is in contact with the floor
What is mass in units of kilograms of a container filled : The density of gasoline is 0.72 grams per cubic centimeter. What is the mass in units of kilograms of a 5-gallon container filled completely with gasoline Ignore the mass of the container.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the current in the line feeding the three loads

Two machines and a lighting load are connected in parallel to a 240 V(rms), 60 Hz line. The first machine uses 230 kW of power at 0.85 power factor lagging. The second machine uses 95 kVA at 0.882 power factor leading. The lightening load consumes..

  What is the peak magnitude of b of the incident wave

A circular loop TV antenna with 0.01 m2 area is in the presence of a uniform -amplitude 300 MHz signal. When oriented for maximum response, the loop develops an emf with a peak value of 20 mV. What is the peak magnitude of B of the incident wave?

  Estimate probability that subscriber uses at least 500 min

The duration of a cellular call is an exponential random variable with expected value of 3 minutes. A subscriber makes 120 calls each month. Use the central limit theorem to estimate the probability that the subscriber uses at least 400 minutes.

  What is the internal resistance of the battery

When the starter motor, which draws 90A, is running the terminal voltage drops to 11V. What is the internal resistance of the battery What percentage of the chemical power is delivered to the starter motor

  How many address lines are needed to address the memory

(a) Howmany 256M X 16 RAMchips are needed to provide amemory capacity of 8 GB (b) How many address lines are needed to address this memory (c) How many address lines need to go to each chip

  Find what is the maximum possible data rate

A communications channel has a bandwidth of 2,000 Hz and a signal-to noise-ratio (SNR) of 20 dB. What is the maximum possible data rate

  What should be the filter''s passband cut-off frequency

What should be the filter's passband cut-off frequency?(DSP Question).

  Calculate the developed torque at full load

A 480V, 60 Hz three phase induction motor has the following parameters: R1=R' 2= .3 ohms Xeq= 1 ohm Xc=600 ohms At full load, the motor speed is 1120 rpm, the rotational loss is 400W and the core loss is 1 kW.

  Find force f on current element assuming b field constant

A current element of length 1cm is located at (1m, 3m, 4m) in free space and carries a current of 20mA along ay. An infinitely long filamentary current of 12A along az passes through the coordinate origin (0,0).

  Determine cutoff frequency and order for anti-image filter

a dsp system is given with the following specifications: design requirements: sampling rate 20,000 Hz Maximum allowable gain variation from 0 to 4,000 Hz = 2dB 40dB rejection at the frequency of 16000 Hz

  Find what is the probability of three heads

An experiment consists of tossing a fair coin four times in succession. What are the possible outcomes Now count up the number of outcomes with three heads. If the outcomes are equally probable, what is the probability of three heads

  Determine the maximum gain of the antenna

A single-turn resonant circular loop with a /8 radius is made of copper wire with a wire radius of 10^4 pi f/2 and conductivity of 5.7 × 10^7S/m. For a frequency of 100 MHz, determine, assuming uniform current

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd