Determine atsteady state the volumetric flow rate of air

Assignment Help Mechanical Engineering
Reference no: EM13626640

The small two-story office building shown in Fig.P4.10 has 36,000 ft3 of occupied space. Due to cracksaound windows and outside doors, air leaks in on the windward sideof teh building and leaks out on the leeward side of the building.Outside air also enters the building when outer doors are opened.On a particular day, tests were conducted. The outdoor temperaturewas measured to be 15 degrees F. The inside temperature wascontrolled at 70 degrees F. Keeping the doors closed, theinfiltration rate through the cracks was determined to be 75ft3/min. The infiltration rate associated with dooropenings, averaged over the work day, was 50 ft3/min.The pressure difference was negligible between the inside andoutside of building. (a) Assuming ideal gas behavior, determine atsteady state the volumetric flow rate of air exiting the building,in ft3/min. (b) When expressed in terms of teh volume ofthe occupied space, determine the number of building air changesper hour.

Reference no: EM13626640

Questions Cloud

In an oil refinery methane gas ch4 enters a compressor at a : in an oil refinery methane gas ch4 enters a compressor at a steady rate of 0.9 kgs and at a pressure 2 bar temperature
An insurance policy costs 100 and will pay policyholders : an insurance policy costs 100 and will pay policyholders 10000 if they suffer a major injury or 3000 if they suffer a
A what is the smallest value of r such that a minimum in : a 900 hz sound wave is produced on the source side of the tube shown in the figure. the sound travels to the right
A commuter must pass through five traffic lights on her way : a commuter must pass through five traffic lights on her way to work and will have to stop at each one that is red. she
Determine atsteady state the volumetric flow rate of air : the small two-story office building shown in fig.p4.10 has 36000 ft3 of occupied space. due to cracksaound windows and
A 15 kg block b is being pulled along a smooth surface by : a 15 kg block b is being pulled along a smooth surface by a winch a. assume the winch is a 10 kg disc with a constant
The rayleigh criterion can be used to determine if the : in the game of baseball the catcher uses his fingers to send a sign to the pitcher telling what pitch to throw next.
How many total interstitial sites are there in one cubic : a for pt at 20 c calculate how many unit cells there are per cubic meter.bhow many total interstitial sites are there
Consider an m state markov chain with transition matrix pij : consider an m state markov chain with transition matrix pij. note as usual the sum of the entries in any row add to

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd