Determine at which of the two points the elevation is higher

Assignment Help Civil Engineering
Reference no: EM13297337

Liquid butaneis flowing through a pipe of variable diameter. Assume that the flow is inviscid and steady. At point 1in the pipe, the velocity and pressure are measured to be 32 ft/s and 20 psi. At point 2, the velocity and pressure are 14 ft/s and 23 psi. Determine at which of these two points the elevation is higher. Calculate the height difference. (Assume the sp ecific gravity of butane is 0.6 and that the butane is at a temperature of 15 C.)

Reference no: EM13297337

Questions Cloud

Convert all quantities to si units then convert it to mph : Assume the plane is flying at an altitude of 32,810 ft (10 km), where the temperature is -8 C and the pressure is 250 mb. The Pitot-static tube measures a piezometric pressure difference corresponding to 1.206 psi. What is the airspeed in both m/s..
What is the optimal decision for this investor : Draw a decision tree for this problem and what is the optimal decision for this investor and what is the EMV for this decision?
How far from you is the fish : You're standing in waist-deep water with your eyes 0.44 m above the surface. A fish is swimming 0.55 m below the surface. How far (horizontally) from you is the fish
Explain activation energy for the gas phase decomposition : The activation energy for the gas phase decomposition of trichloromethyl chloroformate is 174 kJ. ClCOOCCl3 2 COCl2 The rate constant at 551 K is 4.72E-4 /s. The rate constant will be 4.96E-3 /s at K
Determine at which of the two points the elevation is higher : At point 2, the velocity and pressure are 14 ft/s and 23 psi. Determine at which of these two points the elevation is higher. Calculate the height difference. (Assume the sp ecific gravity of butane is 0.6 and that the butane is at a temperature o..
Determine the angular frequency of the oscillation : A particle moves along the x axis. It is initially at the position 0.190 m, moving with velocity 0.250 m/s and acceleration -0.350 m/s2. Find the angular frequency of the oscillation
Explain concentrations of both reactants and products : Which statement is true for a reaction with Kc equal to 2.43 × 10-12? A) Increasing the temperature will not change the value of Kc. B) There are appreciable concentrations of both reactants and products.
What was its charge for depreciation and amortization : Pearson Brothers recently reported an EBITDA of $6.5 million and net income of $1.95 million. It had $2.21 million of interest expense, and its corporate tax rate was 35%. What was its charge for depreciation and amortization?
Develop 95 percent confidence interval for population mean : a simple random sample of 20 items from a normal population resulted in a sample mean of 17.25 and a sample standard devation of 3.3 a. develop a 90% confidence interval for the population mean. b. develop a 95% confidence interval for the populatio..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the normal and shear stress on planes making angle

a tension member with cross-sectional area 3 in2 resists a load of 10 kips. How do you Calculate the normal and shear stress on planes making a 0, 20, 45, and 60 angle with the transverse section.

  What is the 2-4-6-trichlorophenol concentration in ppm

A 500 L (132 gal) tank contains 255 mg/L 2,4,6-trichlorophenol dissolved in trichloroethylene (TCE). What is the 2,4,6-trichlorophenol concentration in ppm Assume the temperature of the system is 20 degrees C.

  Calculate the change in temperature of the air in the room

Incandescent light bulbs have been phased out in the US because they are very inefficient (i.e., they produce a very large amount of heat). A 10 W light-emitting diode lamp (LED) can produce about the same light output as incandescent light bulbs

  Compounds empirical and molecular formula

A Silane contains 90.31 % silicon and 9.69 % hydrogen by mass. The compound has a molar mass of 62 g/mol. Determine the compound's empirical and molecular formula.

  Dry unit weight of material

A soil borrow material in its natural state in the ground has a unit weight of 118pcf. Its natural water content is 7%. What is the dry unit weight of this material?

  Bernoulli equation-measure the flow rate through the meter

The meter inlet and throat are connected by the two legs of a mercury manometer. Use the Bernoulli equation to describe how this manometer can be used to measure the flow rate through the meter.

  Wall shear stress and friction velocity

A rectangular channel 5 m wide carries a discharge of 10 m^3/s at a uniform depth of 3 m. The channel is running on a slope of 0.0025 m/m. Estimate wall shear stress and friction velocity. Assume the density of flowing water as 1000 kg/m^3.

  Calculate the elastic recovery

A 10-mm diameter bar of 1040 carbon steel is subjected to a tensile load of 50,000 N, taking it beyond its yield point. Calculate the elastic recovery (or strain) that would occur upon removal of the tensile load.

  Determine the cartesian coordinates of the anchor

A fisherperson, pulling on the anchor cord, causes a force on the man of F=(40i+20j-50k)N. If the cord is 30m long,determine the Cartesian coordinates of the anchor at A. Assume that cord OA is a straight line.

  Determine both the point of tangent and deflection angles

The point of intersection of the tangents is located at station (948+67.32). If the design speed of the highway is 60mi/h, determine both the point of tangent and the deflection angles to whole stations for laying out the curve. Select appropriate..

  Hydraulic behaviour in open channel

Describe how test flumes and associated equipment are used to assess and confirm hydraulic behaviour in open channel

  Width of the footing if factor of safety given

Characteristic values of the shear strength parameters of the soil are c'= 0, and f' = 400. Determine the required width of the footing if a factor of safety of 3.0 against shear failure is specified when the water table rise to foundation level.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd