Determine and plot the required motor torque

Assignment Help Mechanical Engineering
Reference no: EM13935699

1. A motor attached to the shaft at O causes the arm OA to rotate over the range 0 () 180°. The un- stretched length of the spring is 0.65 m, and it can support both tension and compression. If the net moment about O must be zero, determine and plot the required motor torque M as a function of ().

1823_Determine and plot the required motor torque.png

2. The tension T in cable AB is maintained at a constant value of 120 N. Determine the moment MO of this tension about point O over the range 0 () 90°. Plot the x-, y-, and z-components of MO as functions of ().

1010_determine and plot the required motor torque1.png

Reference no: EM13935699

Questions Cloud

What factors that normally are not relevant for project : What additional factors that normally are not relevant for a purely domestic project deserve consideration in multinational capital budgeting?
What are tools and strategies to increase traffic website : Select a web site from an education industry (university, school or training center) and analyze the ease of use of at least 3 functions and/or features?
Explain two ways in which urine may become contaminated : Explain three different ways in which antibodies react with antigens that they are specific to that aid in preventing colonization or infection in the host.
Measure the effectiveness of the recruiting efforts : How would you suggest they measure the effectiveness of their recruiting efforts?
Determine and plot the required motor torque : Determine the moment MO of this tension about point O over the range 0 () 90°. Plot the x-, y-, and z-components of MO as functions of ().
How simulation can be use in multinational capital budgeting : Explain how simulation can be used in multinational capital budgeting. What can it do that other risk adjustment techniques cannot?
The increase in cost was obvious : The increase in cost was obvious. Material and labor had remained fairly constant per foot of pipe, but over head costs, which were $0.15 per foot in 2011, had increased to $0.26 in 2012.
In what ways is estimated npv of the project more uncertain : In what ways is the estimated net present value of this project more uncertain than that of a similar project in a more developed European country?
Tweleve months strategic hr plan for the organisation : Group research project report: Strategic Human Resource management Twelve Month plan'. For this assessment, we need to assume that our group is the HR management team for an authentic profit-seeking organisation. Our task is to develop a new 12 mo..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the time required and the distance traveled

An elevator descends from rest with an acceleration of 5 ft>s2 until it achieves a velocity of 15 ft>s. Determine the time required and the distance traveled.

  One kilogram of water contained in a sealed piston-cylinder

one kilogram of water contained in a sealed piston-cylinder assembly initially at 160degc and 200 kpa undergoes an

  Heat engine operates between reservoirs

A heat engine operates between reservoirs at 1000 and 300 K. Some of the power output from the heat engine drives a refrigerator which operates between 250 and 300 K. The heat-transfer input at 1000 K to the heat engine is 1000 kJ, and the heat trans..

  Find the power output in mw and the thermal efficiency

Consider a 2500 psia/1000 F turbine inlet, single reheat to 1000 F cycle with a reheat pressure ratio of P2/P1= 0.2 and a steam mass flow rate of 2 x 10^6 ibm/hr. The condensor operates at a pressure of 1 psia. Pump and turbine isentropic efficiencie..

  Derive the scaling relation for the strain energy release

derive the scaling relation for the strain energy release rate of crack extension under fixed displacement. clearly

  Distance from the horizontal top surface of the cube

A cube of wood having an edge dimension of 20.0 cm and a density of 650 kg/m3 floats on water.

  What is bubble pressure for an equimolar mixture

The system acetone(1) and methanol(2) is well represented by the one parameter Margules equation using A = 0.605 at 50 degrees C. a) What is bubble pressure for an equimolar mixture at 30 C?

  The machines steady state amplitude is measured as 15 mm

a 45 kg machine is mounted on a spring of stiffness 8 times 10 5 nm. when the machine operates at 32 hz. the machines

  If the mercury level in the manometer is higher on the side

a mercury manometer ?13600 kgm3 is connected to an air duct to measure the pressure inside. the difference in the

  Air undergoes a polytrophic process in a piston cylinder

Air undergoes a polytrophic process in a piston cylinder assembly from p1=1 atm, T1=70 degrees F to p2=5 atm. Employing the ideal gas model with constant specific heats at 80 degrees F, determine the work and heat transfer per unit mass,

  Determine the maximum weight of block c if block b is not

a 10-lb block b rests as shown on a 20-lb bracket a. the coefficients of friction are us0.3 and uk0.25 between block b

  A heat pump with a cop of 30 is used to heat air contained

a heat pump with a cop of 3.0 is used to heat air contained in a 1205.4m3 of well-insulated rigid tank. initially the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd