Determine a the pump work wk per kilogram of steam b the

Assignment Help Mechanical Engineering
Reference no: EM13607817

Steam having a specific Enthalpy of 160 kJ/kg and pressure of 1 kPa enters as adiabatic pump. Upon leaving the pump, the steam is at a pressure of 1200 kPa and has a specific enthalpy of 170 kJ/kg. No kinetic or potential energy changes occur through the pump. Determine (a) the pump work, wk, per kilogram of steam (b) the average density of steam, assuming that the pump is reversible in nature.

Reference no: EM13607817

Questions Cloud

A pressure gage connected to a tank of oxygen reads 50 psi : a pressure gage connected to a tank of oxygen reads 50 psi and the temperature of the oxygen is 80degf. if the local
Airline managers expect that only about 15 will say yes : suppose an airline decides to conduct a survey of its customers to determine their opinion of a proposed one-bag limit.
Draw a schematic of the system using electric resistance : tankless point-of-use water heaters are commercially available and are claimed to reduce energy usage since water is
Determine the magnitude of the particles displacement from : a particle is traveling with a velocity of v 3sqrtte-0.2ti 4e-0.8t2j ms where t is in seconds. determine the magnitude
Determine a the pump work wk per kilogram of steam b the : steam having a specific enthalpy of 160 kjkg and pressure of 1 kpa enters as adiabatic pump. upon leaving the pump the
Calculate the flow energy per pound-mass enthalpy and : calculate the flow energy per pound-mass enthalpy and total enthalpy. two kilograms of ammonia at 200kpa .755 m3kg and
The following probability distribution represents the : the following probability distribution represents the number of people living in a household x and the probability of
The lifetime of a semiconductor laser has a lognormal : the lifetime of a semiconductor laser has a lognormal distribution and it is known that the mean and standard deviation
The weights of ripe watermelons grown at mr smiths farm : the weights of ripe watermelons grown at mr. smiths farm are normally distributed with a standard deviation of 2.7 lb.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the entropy change of the water during process

A piston-cylinder device is insulated and contains 0.005 m3 of saturated liquid water at a constant pressure of l50 kPa. An electric resistance heater inside the cylinder is now turned on, and 1800 kJ of energy is transferred to the steam.

  A projectile is fired at an angle of 62deg from the

a projectile is fired at an angle of 62deg from the horizontal with a velocity of 704 ftsec. if it lands 4.75 seconds

  Find equations for rtheta periodtheta vtheta tensiontheta

consider a conical pendulum that is a ball of mass m at the end of a string of length li moving in a horizontal circle

  Given that the elastic modulus and poissons ratio of the

a cylindrical bar of metal having a diameter of 18.4 mm and a length of 192 mm is deformed elastically in tension with

  Determine the distance it travels before it starts

determine the time it takes for the ball to start rolling without slip and its speed when it does so. In addition, determine the distance it travels before it starts rolling without slip. Assume (mu)K = 0.10.

  What is a beam

What is a beam? What factors determine the maximum load that it can take without failure?

  An electric motor of total weight 3330 pounds is mounted on

an electric motor of total weight 3330 pounds is mounted on a simply supported beam with an overhang as shown

  A thermopane window consists of two pieces of glass k 078

a thermopane window consists of two pieces of glass k 0.78 wmk 7 mm thick that enclose an air space k 0.026 wmk 7 mm

  What is the actual strain

You have a 120 Ω quarter bridge 2 wire set up with Sg=2.10 and an unknown lead wire resistance. A 59880Ω calibration resistor is switched in parallel to the gage only and a recording instrument is set to give a -100 mm deflection for this calibrat..

  What conditions the use of carburetor heat be detrimental

Under what conditions would the use of carburetor heat be detrimental?

  List and explain three process parameters

h injection molding was portions of the part not filling. List and explain three process parameters that may aid in the correction of this error. What other errors might adjustments in these parameters help allay?

  Calculate net positive suction head (npsh) for the system

A pump station has been designed to lift water out of a 6 metre deep pit (vented to atmosphere) via a centrifigual pump mounted at ground level.   Calculate the Net Positive Suction Head (NPSH) for the system ?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd