Determine a the maximum temperature in the cycle the net

Assignment Help Mechanical Engineering
Reference no: EM13612571

A four-cylinder, four-stroke, 2.8-liter compression-ignition engine operates on the ideal dual cycle with a compression ratio of 14. The air is at 95 kPa and 55oC at the beginning of the compression process and the engine speed is 3500 rpm. Equal amounts of fuel are burned at constant volume and at constant pressure. The maximum allowable pressure in the cycle is 9 MPa due to material strength limitations. Using constant specific heats at 850 K, determine (a) the maximum temperature in the cycle, (b) the net work output and the thermal efficiency, (c) the mean effective pressure and (d) the net power output. Also determine (d) the second-law efficiency of the cycle and the rate of exergy output with the exhaust gases when they are purged assuming the source temperature is equal to the maximum temperature in the cycle and the sink temperature is 25oC.

Reference no: EM13612571

Questions Cloud

Cash flows information what information does the cash flow : cash flows information what information does the cash flow statement provide that you cannot see in the other financial
Sketch the cycle on a t-s diagram with respect to : water is the working fluid in an ideal vapor power cycle with reheat. superheated vapor enters the first turbine stage
The speed of an automobile traveling due to east is : the speed of an automobile traveling due to east is uniformaly reduced from 75.0km to 45.7kmh in a distance of 88.5m.a
A hockey puck on a frozen pond with an initial speed of : a hockey puck on a frozen pond with an initial speed of 18.9 ms stops after sliding a distance of 240.3 m. calculate
Determine a the maximum temperature in the cycle the net : a four-cylinder four-stroke 2.8-liter compression-ignition engine operates on the ideal dual cycle with a compression
What is the mass of the spaceship and the acceleration due : a spaceship is heading toward a planet. while descending to the surface its rockets produce 25 kn of upward thrust and
The net income reported on the income statement for the : the net income reported on the income statement for the current year was 225000. depreciation recorded on plant assets
An industrial psychologist wishes to study the effect of : an industrial psychologist wishes to study the effect of motivation on sales in a particular firm. 24 new salespersons
An electron and a proton starting from rest are accelerated : an electron and a proton starting from rest are accelerated through an electric potential difference of the same

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd