User Account

All Pages

Determine a the exergetic effectiveness and b the exergy

Assignment Help Mechanical Engineering
Reference no: EM13631607

Refrigerant 134a at -10°C, 1.4 bar and a mass flow rate of 280 kg/hr enters an insulated compressor operating at steady state and exits at 9 bar. The isentropic compressor efficiency is 82%. Determine (a) the exergetic effectiveness and (b) the exergy destroyed. The surrounds can be taken to be To= 20°C, Po = 100 kPa.

Reference no: EM13631607

Questions Cloud

The bullet remains embedded in the block which is observed : a 4.50g bullet is fired horizontally into a 2.35kg wooden block resting at the bottom of a 25 degree inclined surface.
If the power generated by the turbine is 75 mw determine : steam expands in a turbine steadily at a rate of 36048 kgh entering at 8 mpa and 600degc and leaving at 20 kpa as a
A muon and an antimuon are moving in opposite directions : a muon and an antimuon are moving in opposite directions with velocities of -0.7 c and 0.7 c respectively. when they
After the pressures but not the temperature in the two : an isolated chamber with rigid walls is divided into two equal compartments one containing steam at 10 bar and 370oc
Determine a the exergetic effectiveness and b the exergy : refrigerant 134a at -10degc 1.4 bar and a mass flow rate of 280 kghr enters an insulated compressor operating at steady
A rigid 10 m3 tank contains water initially at 120degc with : a rigid 1.0 m3 tank contains water initially at 120degc with 50 liquid and 50 vapor by volume. a pressure-relief valve
A well-insulated rigid tank contains 8 kg of a saturated : a well-insulated rigid tank contains 8 kg of a saturated liquid-vapor mixture of water at 100 kpa. initially three
Consider the following give your answers correct to two : consider the following. give your answers correct to two decimal places.a find the standard score z such that the area
Air initially at 27 degrees c is contained in a : air initially at 27 degrees c is contained in a piston-cylinder. calculate the minimum work required to compress the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Evaluate the maximum possible efficiency actual

consider the ocean thermal energy conversion system given in the lecture notes. also take into consideration that 30 of

  The temperature outside is 0 c if it is calm and the heat

suppose you are outside on a cold day with no gloves. assume your hands have an area of 0.01 m2. the temperature of

  At the instant it passes through an altitude of 20000 ft

at the instant it passes through an altitude of 20000 ft above sea level what are the temperature pressure and density

  Re for a specified quanity of heat transfer to the system

a piston cylinder assembly contains a fixed amount of a gas at a given temperature and pressure. for a specified

  This nuclide is produced by the endoergic reaction 16onp16n

an important radionuclide produced in water-cooled nuclear reactors is 16n which has a half-life of 7.13 s and emits

  A horizontal 500 lb force performs at a point d of

a horizontal 500 lb force performs at a point d of crankshaft ab which is held in static equilibrium by a twisting

  Determine the heat transfer coefficient and the amount of

an experiment is to be conducted to determine heat transfer coefficient on the surfaces of tomatoes that are placed in

  A hydraulic cylinder is diameter

A hydraulic cylinder is 100mm diameter and is fed by a pipe 15mm in diameter. If the piston in the cylinder moves forward at a rate of 0.2ms^1

  This allows the free-stream velocity to remain constant at

a wind tunnel has a 1-m2 6-m-long test section in which air at standard sea-level conditions moves at 70 ms. it is

  The ammonia is then cooled so that it is a saturated liquid

a piston-cylinder contains 1 lbm of a saturated ammonia at 70 degrees farenhight and 85 quality. the ammonia is then

  If the mean radius is 024 m and this is constant throughout

a high-pressure axial compressor for a jet engine rotates at 15000 rpm with an overall stagnation pressure ratio of

  Determine the maximum weight of block c if block b is not

a 10-lb block b rests as shown on a 20-lb bracket a. the coefficients of friction are us0.3 and uk0.25 between block b

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd