User Account

All Pages

Determine a overall efficiency of the pump-motor unit and b

Assignment Help Mechanical Engineering
Reference no: EM13619035

Water is to be pumped from a dam to a storage tank 20 m above at a rate of 70 L/s. The electric power needed to achieve this is 20.4 kW. Neglecting the frictional losses in the pipes and the change in the K.E, determine a) overall efficiency of the pump-motor unit and b) the pressure difference between the inlet and the exit of the pump. Draw the process diagram.

Reference no: EM13619035

Questions Cloud

Houma bio-control has hired you as a consultant to assess : houma bio-control has hired you as a consultant to assess the economic feasibility of investing 2500000 to purchase a
Obtain a relation for the variation of pressure in the : temperature varies with altitude. the variation in the temperature can be approximated by tt0 -beta z where t0 is the
The board for colton industries is considering a proposal : the board for colton industries is considering a proposal by the ceo to sell the firms boat manufacturing division. an
Determine the volume flow rate and the density of the gas : carbon dioxide gas enters a pipe at 3 mpa and 500 k at a rate of 2 kgs. the gas is cooled at constant pressure as it
Determine a overall efficiency of the pump-motor unit and b : water is to be pumped from a dam to a storage tank 20 m above at a rate of 70 ls. the electric power needed to achieve
At year-end 2013 wallace landscapings total assets were 217 : at year-end 2013 wallace landscapings total assets were 2.17 million and its accounts payable were 560000. sales which
You work for a consumer watchdog publication and are : you work for a consumer watchdog publication and are testing the advertising claims of a light bulb manufacturer. the
A scaffold of mass 56 kg and length 55 m is supported in a : a scaffold of mass 56 kg and length 5.5 m is supported in a horizontal position by a vertical cable at each end. a
Calculate point estimates of the population variance and : data on pull-off force pounds for connectors used in an automobile engine application are as follows 79.3 75.1 78.2

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Evaluate the maximum possible efficiency actual

consider the ocean thermal energy conversion system given in the lecture notes. also take into consideration that 30 of

  Electric-circuit which is called a phase

Shows an electric-circuit which is called a phase-lag network. Derive the transfer function and consider the above bock-diagram of figure (3). You are now required to derive the transfer function Y(s)/R(s), by using the signal flow graph meth..

  A exit p2 - 147 psia v2 2677 ft3lb and u2 10775 btulb

there are supplied to a nozzle 2400 lbhr of steam at an absolute pressure of 200 psia. at the entrance v1 6000 ftmin

  The desire is to raise the temperature of the ambient air

The desire is to raise the temperature of the ambient air from 60 degree F to 350 degrees F ---- I need to calculate the amount of steam energy in BTU's per minutes and lbs of steam per minute necessary to accomplish the increase in air temperatur..

  A 75-lb stoplight is suspended between two poles as shown

a 75-lb stoplight is suspended between two poles as shown in fignbspp3-27. neglect the weight of the flexible cables

  Heat transfer between the compressor and its surroundings

refrigerant 134a enters a compressor operating at steady state as saturated vapor at -4 degc and exits at a pressure of

  How to create a directory called class

make a text file that contains what is your absolute path, and call it paths.txt

  Calibrated vibrometer output indicates a velocity amplitude

the waveform from a mechanical vibration is sensed by a velocity-sensitive vibrometer. the oscilloscope trave indicates

  What is the airflow speed in the stream tube at a location

a single stream tube is selected to characterize the air flow past the wing of an aircraft in flight at an altitude of

  Determine the resulting force created by the vehicle and

a construction vehicle of mass 30 mg is used to unload sand in a horizontal line through a port on the bottom of the

  Calculate the actual power transmitted to the second pulley

Calculate the actual power transmitted to the second pulley and calculate the power which can be transmitted if the maximum tension in the belt is limited to half of the ultimate strength of the belt.

  Define shearing stress

Two bars, one having a circular section of radius b, the other an elliptic section with semiaxes a,b. For equal angles of twist, which bar experiences the larger shearing stress?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd